699578
5
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
CA-6 SATEL 3
The zones (input lines) can perform the following functions in the system:
00 exit/entry the violation of which, when in the armed mode, will start countdown of the entry
delay time and will enable the delay for INTERIOR DELAY type zones (violation of an
INTERIOR DELAY zone without prior violation of the ENTRY/EXIT zone will trigger an
alarm immediately). Upon violation, a “zone violation” code is sent to the report station
(it is possible to skip sending this message), and, after counting down the "entry delay
time" and triggering the alarm – a “zone alarm” code. The "entry delay" countdown can be
signaled in the keypad. It is possible to define automatically bypassing zones if no
ENTRY/EXIT zone is violated during the exit delay time. Because of its additional
functions, this zone type cannot be used as a common zone for both partitions.
01 delayedwhen violated in the armed mode, it starts delay countdown, after which an alarm is
triggered. It will not occur if the zone is disarmed before completion of the delay
countdown. Upon violation, a “zone violation” code is sent to the report station, after
counting down the entry delay time and triggering the alarm – a “zone alarm” code.
The delay is not signaled in the keypads.
02 interior delayed when violated in the armed mode after previous violation of the
ENTRY/EXIT zone, it behaves like a DELAY zone. When violated in the armed mode
without previous violation of the ENTRY/EXIT zone, it behaves like an INSTANT zone.
03 instant – when violated in the armed mode, it immediately triggers an alarm and sends a ”zone
alarm” message to the monitoring station.
04 day/night when violated in the armed mode, it behaves like an INSTANT zone, while when
disarmed, it will signal violation in the keypad (unless function is disabled FS20, second
set, option 3) and send a “zone violation” code to the station.
05 counting L1 when violated in the armed mode, it increases the status of the first of three
violation counters (a “zone violation code is sent to the station), until the number of
violations specified for that counter is exceeded (programming in FS7). Then the violation
triggers an alarm (a ”zone alarm” code is sent to the report station). By default, the count-
up time is set at 30 seconds. It is possible to program another counter count-up time
(FS123). If the preset number of violations is not reached within this time, it will be reset.
The next zone violation will start the add-up procedure all over again. The violations are
added up starting from zero, and the count-up time starts upon the first violation after
resetting the counter. The "counting L1" function can be assigned to more than one zone,
in that case violations of those zones will be summed up. The zone will trigger an alarm
upon exceeding the programmed number of violations added up by a given counter.
Alarm can also be triggered after resetting the counting zone counter, if the zone
associated with the given counter is still violated.
06 counting L2 operation identical as for the "counting L1", but changes the status of the
second of the three counters.
07 counting L3 operation identical as for the "counting L1", but changes the status of the third
of the three counters.
08 24H audible armed all the time, irrespective of whether the partition it is assigned to is
armed, or not. Each violation of this zone will trigger alarm on the “burglary alarm” type
outputs, in the keypad and will send a “zone alarm” code. It makes possible to create
tamper circuits and panic buttons.
09 24H auxiliary armed all the time, irrespective of whether the partition it is assigned to is
armed, or not. Each violation of this zone will trigger an alarm in the keypad and will send
a “zone alarm” code. It is intended for connecting detectors such as gas or flood sensors,
etc.
10 24H silent armed all the time, irrespective of whether the partition it is assigned to is armed,
or not. Violation of this zone will only send a “zone alarm” code to the monitoring station.
11 24H fire armed all the time, irrespective of whether the partition it is assigned to is armed,
or not; intended for the fire detectors.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-6 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel CA-6

Satel CA-6 Aanvulling / aanpassing - Deutsch - 19 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel CA-6 Installatiehandleiding - Deutsch - 80 pagina's

Satel CA-6 Gebruiksaanwijzing - Deutsch - 18 pagina's

Satel CA-6 Aanvulling / aanpassing - English - 40 pagina's

Satel CA-6 Snelstart handleiding - English - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info