699870
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
SATEL ARF-100 3
press the button to toggle between simulation of the device powered from an
external source and simulation of the device powered from a battery. After switch-
on the tester simulates operation of the device powered from an external source.
Which power supply method is being simulated is indicated by the LED .
Press and hold down the button to change the refresh rate of the radio signal level
indicator . After switching the tester on, the indicator refresh takes place during
polling and is signaled by one short beep. If you hold down the button longer than
3 seconds, the tester will enter and remain in the dense polling mode until the
button is released. When in this mode, the indicator is refreshed every 2 seconds,
which is signaled by two short beeps.
radio signal level indicator. The indicator consists of 7 LEDs (2 yellow and 5 green ones),
which present percentage of the radio signal level (15 – 100%). Intensity of the LED
lighting depends on which device is simulated by the tester. If a battery-powered device
is being simulated, the LED light is weaker. If, when the LEDs are ON, you change the
power supply method (by pressing the button), the LEDs will go off. They will only go
on again during the next polling and will show an updated radio signal level. If the tester
battery is low, all the indicator LEDs are blinking.
red LED indicating the tester operating mode:
ON checking the level of radio signal received by the tester from the ABAX
controller / control panel,
flashing checking the level of radio signal received by the ABAX controller / control
panel from the tester.
red LED indicating how the device being simulated is power supplied:
ON powered from battery (e.g. AMD-100, AMD-101 and APD-100 detectors,
ASP-205 siren),
OFF powered from an external source (e.g. ACX-200 expander, ASP-105 siren,
ASW-100 wireless controller).
4. Start-up and testing the radio signal level
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the battery. The
manufacturer is not liable for the consequences of incorrect installation of the
battery.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
1. Install the battery and switch the tester on.
2. Add the tester to the wireless system (see the manual for ACU-120 / ACU-270 controller
or the installer manual for INTEGRA 128-WRL / VERSA / VERSA Plus / VERSA IP
control panel). The serial number of each tester is 0000500.
3. Use the button to define how the device simulated by the tester is supplied.
4. Start the test mode on the ABAX controller / control panel.
5. Place the tester in the location intended for installation of wireless device and check the
level of radio signal received by the tester from the ABAX controller / control panel and
the level of signal received by the ABAX controller / control panel from the tester. If the
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel ARF-100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel ARF-100 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel ARF-100

Satel ARF-100 Gebruiksaanwijzing - Nederlands - 4 pagina's

Satel ARF-100 Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info