699875
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
SATEL AOD-200 5
2. Install the battery and secure it with the clip you will find in the package.
3. Add the detector to the wireless system (see the ACU-120 / ACU-270 controller manual or
the INTEGRA 128-WRL / VERSA / VERSA Plus / VERSA IP control panel installer
manual). The sticker with 7-digit serial number which shall be entered when registering
the detector in the system can be found on the electronics board.
4. Replace the cover.
5. Fasten the detector temporarily at the place of its future installation.
6. Check the level of signal received from the detector by the ACU-120 / ACU-270 controller
or the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select
another place for installation. Sometimes, it is sufficient to shift the device ten or twenty
centimeters to obtain a considerable improvement in the signal quality.
7. Remove the front cover (Fig. 4).
8. Remove the electronics module (Fig. 5).
9. If the detector is to be mounted on angle bracket or ball bracket, make a hole in the
enclosure base for the additional tamper switch cables.
10. Mount the enclosure base to the wall, to the angle bracket (see: “Angle bracket
mounting”) or to the ball bracket (see: “Ball bracket mounting”). Use screw anchors
suitable for the mounting surface (concrete wall, drywall, etc.). The screw anchors should
guarantee required mechanical strength. In Figure 6 possible ways of mounting the
detector are shown.
11. Having secured the detector, mount the electronics module and replace the cover.
12. Configure the detector settings:
sensitivity of PIR sensor,
sensitivity of microwave sensor,
sensitivity of dusk sensor (detection threshold).
For description on how to configure the detector, refer to the ACU-120 / ACU-270
controller manual or the INTEGRA / VERSA / VERSA Plus / VERSA IP control panel
programming manual.
If the detector is to be pet immune, for the infrared and microwave sensors do not set
the detection sensitivity higher than default.
13. Start the test mode and check that the motion within the detector area will light up the
LED. Fig. 11 shows:
- the maximum coverage area, - creep zone.
14. End the test mode.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel AOD-200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel AOD-200 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel AOD-200

Satel AOD-200 Gebruiksaanwijzing - Nederlands - 10 pagina's

Satel AOD-200 Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info