699871
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
SATEL ACX-200 3
NO1...NO8 - relay output normally open contact.
Z1…Z4 - zone.
4. Installation
Disconnect power before making any electrical connections.
The device is designed for indoor installation. It is recommended that the expander be
mounted high above the floor. This will allow you to get a better range of radio
communication and avoid the risk of the expander being accidentally covered by
people moving around the premises.
1. Loosen the cover locking screws and remove the enclosure cover.
2. Connect the temporary 12 V DC power supply to the expander and add the device
to the wireless system (see the ACU-100 / ACU-250 / ACU-120 / ACU-270
controller manual or the INTEGRA 128-WRL / VERSA / VERSA Plus control panel
installer manual). The sticker with 7-digit serial number which shall be entered
when registering the expander in the system can be found on the electronics
board.
3. Fasten the expander temporarily at the place of its future installation.
4. Check the level of signal received from the expander by the ACU-100 / ACU-250 /
ACU-120 / ACU-270 controller or the INTEGRA 128-WRL control panel. If the
signal level is lower than 40%, select another place for installation. Sometimes, it
is sufficient to shift the device ten or twenty centimeters to obtain a considerable
improvement in the signal quality.
5. Having checked that the selected location of installation ensures the optimum
level of radio signal, disconnect the temporary 12 V DC power supply.
6. Place the enclosure base against the wall and mark location of the mounting
holes.
7. Drill the holes in the wall for wall plugs (screw anchors).
8. Make an opening for wire harness in the enclosure base.
9. Run the wires through the opening made (power wires, cables connecting wired
devices with the expander, etc.).
10. Using wall plugs (screw anchors) and screws, secure the enclosure base to the
wall.
11. Connect detectors to the expander zones. For the EOL configuration, use a 2.2 k
resistor, and for the 2EOL configuration – two 1.1 k resistors.
12. If the tamper switch is to be supervised, connect the tamper output terminals to
the expander zone (you can connect the tamper output in parallel with the detector
and configure the expander zone as 2EOL).
13. Connect the devices to the expander outputs.
Note: Given the specific character of radio communication, it is not recommended that
the expander be used in applications where quick switchover of the output
status is expected.
14. Connect 12 V DC power wires to the +12V and COM terminals.
15. Replace the cover and then lock it with the screw.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel ACX200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel ACX200 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel ACX200

Satel ACX200 Gebruiksaanwijzing - Nederlands - 4 pagina's

Satel ACX200 Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info