699609
5
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
SATEL ACX-210 3
precision pliers,
double-sided mounting tape.
1. Connect the temporary power supply (4...24 V DC) to the expander.
2. Add the expander to the wireless system (see the ABAX 2 / ABAX controller manual or
the INTEGRA 128-WRL control panel installer manual). The sticker with serial number
which shall be entered when registering the expander in the system can be found on the
device enclosure.
In the INTEGRA / VERSA alarm system, the expander is identified as ACX-200.
Simultaneous operation of the expander by the ABAX 2 and ABAX controller /
INTEGRA 128-WRL alarm control panel is not possible.
3. If the expander is to be installed in the enclosure of another device (e.g. a detector), put
the expander into that enclosure.
4. Place the expander / device in the enclosure of which the expander is mounted at the
location where it is to be installed.
5. Check the level of signal received from the expander by the ABAX 2 / ABAX controller or
the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select
another place for installation. Sometimes, it is sufficient to shift the device ten or twenty
centimeters to obtain a considerable improvement in the signal quality. You can also try
to turn the expander around to check what effect the change in antenna position will have
on the signal strength level.
The ARF-200 tester makes it possible to check the radio signal strength at the place of
future installation without having to put the expander there.
6. Disconnect the temporary power supply.
7. If the expander is to be mounted inside another device enclosure, run a bunch of wires
into the enclosure so as to make connections referred to in steps 8 to 10.
8. Connect detectors to the expander zones. For the EOL configuration, use a 2.2 k
resistor, and for the 2EOL configuration – two 1.1 k resistors.
9. Connect the devices to the expander outputs.
Given the specific character of radio communication, it is not recommended that the
expander be used in applications where quick switchover of the output status is
expected.
10. Connect the power leads to the +12V and COM terminals (use flexible conductors with a
cross-section of 0.5-0.75 mm
2
).
Do not use the battery to power the expander.
11. Fasten the expander to the mounting surface or, if it is to be installed in the enclosure of
another device, put the expander inside that enclosure. To install the expander, you can
use a double-sided mounting tape.
12. Power up the expander.
13. Configure the expander settings (refer to ABAX 2 / ABAX controller manual or INTEGRA
/ VERSA series control panels programming manual).
Taking into account the requirements of EN50131-3 standard, enter 400 ms when
configuring the sensitivity of alarm zones.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel ACX-210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel ACX-210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel ACX-210

Satel ACX-210 Gebruiksaanwijzing - Nederlands - 6 pagina's

Satel ACX-210 Snelstart handleiding - Nederlands - 2 pagina's

Satel ACX-210 Gebruiksaanwijzing - Deutsch - 6 pagina's

Satel ACX-210 Snelstart handleiding - Deutsch, English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info