699872
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
SATEL ACX-201 3
TMP - tamper input (NC) – if not used, it should be shorted to the common
ground.
Z1…Z4 - zone.
4. Installation
Disconnect power before making any electrical connections.
Never connect two devices with power supply unit to one transformer.
Before connecting transformer to a circuit from which it will be powered,
make sure the circuit is de-energized.
The device is designed for indoor installation. It is recommended that the expander be
mounted high above the floor. This will allow you to get a better range of radio
communication and avoid the risk of the expander being accidentally covered by
people moving around the premises.
The expander requires 18 V AC (±10%) supply voltage. The expander feeding
transformer must be permanently connected to the 230 V AC mains. At the place of
installation, an alternating current circuit that will be always alive must be available.
This circuit should be protected by a suitable safety device. Instruct the owner or user
of the alarm system on how the transformer should be disconnected from the mains
(e.g., indicate the fuse protecting the power circuit).
1. Use the ARF-100 tester to make sure that the radio signal level is adequate at the
location where the ACX-201 expander is to be installed. If the signal level is lower
than 40%, select another place for installation. Sometimes, it is sufficient to shift
the device ten or twenty centimeters to obtain a considerable improvement in the
signal quality.
2. Place the enclosure base against the wall and mark location of the mounting
holes.
3. Drill the holes in the wall for wall plugs (screw anchors).
4. Run the wires through the opening in the enclosure base (power wires, cables
connecting wired devices with the expander, etc.).
5. Using wall plugs (screw anchors) and screws, secure the enclosure base to the
wall.
6. Mount the expander board in the enclosure.
7. Secure the antenna and connect it to the socket on the electronics board.
8. Connect detectors to the expander zones. For the EOL configuration, use a 2.2 k
resistor, and for the 2EOL configuration – two 1.1 k resistors.
9. If the expander is to supervise the enclosure tamper switch, connect the wires of
tamper switch to the TMP and COM terminals. If the expander is not to supervise
the enclosure tamper switch, connect the TMP terminal to the expander COM
terminal.
10. Connect the devices to the expander outputs.
Note: Given the specific character of radio communication, it is not recommended that
the expander be used in applications where quick switchover of the output
status is expected.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel ACX-201 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel ACX-201 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel ACX-201

Satel ACX-201 Gebruiksaanwijzing - Nederlands - 4 pagina's

Satel ACX-201 Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info