31127
5
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
5
INSTALLATION
Placing your VCR on top of or under the TV receiver may
result in interference on the TV screen when the VCR is
on. If this occurs, move the VCR to a position beside the
TV receiver.
AUDIO
LINE1(AUX1)
R
L
IN
IN
OUT
OUT
ANT.IN
VIDEO
VHF/UHF
/CATV
Cable/
Antenna
R-AUDIO-L
VIDEO
IN
OUT
IN
OUT
RF OUT
When using the RF coaxial cable (Supplied)
Connect the 75-ohm Coaxial Cable to RF OUT
(VHF/UHF/CATV) on the VCR. Connect the other end to the 75-
ohm antenna input on the back of the TV.
When using the Audio/Video cable (Not supplied)
If your TV has A/V input jacks, you can connect your VCR’s
AUDIO/VIDEO jacks to the back of your TV.
Direct audio/video connections usually result in better picture
and sound quality for tape playback. Please see your TV’s
owners manual for details on how to set your TV to the VIDEO
mode using the TV/VIDEO button on your TV.
VCR Output Channel Setting
1.
Set the TV to the VCR channel (3 or 4).
2. While the VCR is turned off,
press and hold CHANNEL
(V/v) on the front panel for more than five seconds.
Indicators on the INDICATOR PANEL blinks as follows:
3.
Use CHANNEL (V/v) on the front panel to change the
RF output channel (CH 03 or CH 04).
4.
Turn the VCR off and then on again.
VCR TO TV CONNECTION
ANTENNA TO VCR CONNECTIONS
AUDIO
LINE1(AUX1)
R
L
IN
IN
OUT
OUT
ANT.IN
VIDEO
VHF/UHF
/CATV
IN
OUT
RF OUT
Without Cable Box
If your cable wire is connected to your TV without a converter or
descrambler box, unscrew the wire from your TV and attach it to
the ANT.IN connector on the VCR. Use the supplied round
coaxial cable to connect the VCR’s RF OUT (VHF/UHF/CATV)
connector and the 75 ohm antenna input connector on the TV.
With this connection, you can receive all midband, super band,
and hyperband channels.
With Cable Box
If a converter is required in your cable system, follow the instruc-
tion below.
The cable hookup permits both TV and VCR operation.
To view or record a CATV channel
1 Set the TV to the VCR channel (3 or 4).
2 Set the VCR channel selector to the output channel of the
Cable Converter box by pressing the CH/TRACK (v/V) or the
number buttons (0-9) of your VCR. (Example: CH3).
3 Select the channel to view on the Cable Converter Box.
•With this connection, you CANNOT record one program while
viewing another.
Channel memory programming is not needed when using this
connection.
NOTES
1
Disconnect the antenna leads from the rear of the TV receiver.
2 Identify the type of cable from your antenna. If it is a round
cable as illustrated, it is a 75 ohm coaxial antenna cable. This
cable will connect directly to the connector marked ANT.IN on
your VCR.
If your antenna lead wire is a flat type antenna cable, connect
it to a Antenna Adaptor (300-ohm to 75-ohm) (not supplied)
and slip the Adaptor onto the ANT.IN connector. The Adaptor
does not screw on to the VCR, it just slips over the connector.
(CH 03)
(CH 04)
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sanyo VWM900 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sanyo VWM900 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info