629984
7
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
Owner's Manual
7
XML POWERED MIXERS
Input Channel Section
The following section details each part of the XMLs INPUT CHANNELS including the 3-BAND EQ, the MONITOR and EFX
sends, GAIN and VOLUME controls.
Controls and Functions
1. Peak - This LED indicator will ash RED when the channel input signal peaks.
To reduce distortion, turn the VOL control counterclockwise until the clip
indicator does not light during normal use.
2. Equalizer (HF, MF, and LF) - This three-band equalizer allows you to contour
a channel’s high, mid, and low frequency bands. When the control is set to
the 12 o'clock (detent) position, there is no eect on the signal. Turning the
controls fully clockwise will raise the level of the frequency band +15 dB,
while turning the controls fully counterclockwise will lower the level of the
frequency band -15 dB.
3. AUX 1/MON - The AUX 1 controls the amount of signal sent to the Monitor
bus. The AUX 1 send is pre-fader so the signal is unaffected by the position
of the VOL control. These sends are usually used to create a separate mix for
a monitor system. The Monitor bus signal is routed to the front panel MONI-
TOR jack, and may be routed to the SPEAKER RIGHT/MONITOR output jacks,
depending on the setting of the MODE switch. When the MON send knob is at
the 12 oclock center position, the signal is routed with unity.
4. AUX 2/EFX - The AUX2/EFX send knob allows you to route the signal to the
internal digital eects processor and the EFX 2 SEND output. The AUX2/EFX
send is post-fader so the level of the signal is determined by the position
of the channel Volume control. When the AUX2/EFX send knob is at the 12
oclock position, the signal is routed with unity.
5. VOL - This knob controls the volume of channel inputs and is used to continu-
ously adjust the loudness of the various signals being blended together at
the Main Outputs. Moving the knob counterclockwise causes the signal to be
attenuated. Conversely, when rotated clockwise, the signal is boosted.
NOTE: For best signal-to-noise ratio, all VOL controls for channels carrying
signal should generally be kept at or near the 12 oclock (unity) position.
Channels that are unused should have their Volume controls kept fully coun-
terclockwise at their minimum level.
6. COMP (XML610 and XML910 only) - The COMP knob adjusts the level of
compression applied to the channel. As the COMP knob is turned clockwise,
the compression ratio is raised and the output gain is adjusted accordingly.
The dynamic range of the channel is narrowed, where softer signals will
be magnied and loud signals will be subdued to sit better in the mix. You
should use your ears when adding compression to a signal. Too much com-
pression can create a pumping eect, eliminate all dynamic range, and lead to
feedback.
7. PAD 20 dB switch, Channels 1 to 4 (XML610 and XML910 only) Use this
switch to match the type of input signal you are supplying. If the PEAK light
of an input continues to light even when the VOL is turned down, depress the
PAD switch . Always turn the VOL completely counterclockwise before press-
ing the PAD switch to avoid damaging your speakers.
2
1
3
4
5
6
7
8
9
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Samson XML910 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Samson XML910 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Samson XML910

Samson XML910 Gebruiksaanwijzing - Deutsch - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info