735237
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
KL08NSB
Installation and Wiring Guide
www.salus-controls.com Technical Helpline +44 (0) 1226 323 961
1
Remove the plastic cover. Open (and
close) the four white screws with a
quarter turn only. Note that screws on
opposite sides turn in the opposite
direction.
2
Remove the white terminal connection
board.
3
Attach the back of the KL08NSB to the
DIN rail or wall.
5
Clip all power and thermostat cables
into their correct positions. The
following shows the power, zone 1,
and 2 thermostat cables in position:
6
Replace the white terminal connection
board.
7
Bend over and push the power wires
into the round power holes.
8
Bend over and push all thermostat
wires into the round holes at the top
of the KL08NSB.
9
Push the actuator wires into the round
holes at the bottom of the KL08NSB.
You can connect up to four actuators in
each zone.
10
Make sure there is a fuse in the
fuse holder.
11
Set the actuator and boiler delay
jumpers at the top right of the KL08NSB.
12
Push in the wires for a pump and boiler
(if applicable) at the bottom right of the
KL08NSB.Pump and boiler switching is
volt free.
13
Attach the red strain-relieving strip
using the three screws to secure the
pump and boiler wires to the bottom
side of the KL08NSB.
14
Replace the plastic cover.
15
Switch on mains power supply to the
unit. The red LED comes on.
LED indications
Name Colour Meaning
Power
KL08NSB is supplied with 230V power
Zone 1 actuators
Demand from zone 1 thermostat: actuator open
Zone 2 actuators
Demand from zone 2 thermostat: actuator open
Zone 3 actuators
Demand from zone 3 thermostat: actuator open
Zone 4 actuators
Demand from zone 4 thermostat: actuator open
Zone 5 actuators
Demand from zone 5 thermostat: actuator open
Zone 6 actuators
Demand from zone 6 thermostat: actuator open
Zone 7 actuators
Demand from zone 7 thermostat: actuator open
Zone 8 actuators
Demand from zone 8 thermostat: actuator open
Pump
Pump on
Boiler
Boiler on
Installing and Connecting
the KL08NSB
Use the KL08NSB wiring centre to simply and safely connect
thermostats and corresponding thermal actuators. It can
have three different physical configurations:
Two groups of V30 thermostats, each group having
up to four thermostats.
Three groups of V30 thermostats with a KL04NSB
extension attached, each group having up to four
thermostats.
A VS30 master thermostat controlling up to seven VS35
slave thermostats. For this configuration, you must
make a bridge between grey positions 1-4 and 5-8.
If a KL04NSB extension is attached to the KL08NSB, this
is not included in this configuration and another VS30
master thermostat will control the VS35 slaves connected
to the KL04NSB on zones 9 to 12.
Install the KL08NSB only in dry and closed interior rooms.
Relative air humidity in the room may not exceed 95%.
Clean the KL08NSB only with a dry and soft cloth. Do not
use solvents or aggressive cleaning agents.
4
Cut the power, thermostat and
device cables to length.
Device
Power/Thermostat
50mm
110mm
10mm
10mm
Type of Actuator
The default setting for the type of actuator
is normally closed (NC). To change this setting
to normally open (NO), carefully remove the
jumper and re-insert it in the other position
as shown below. Note that the actuator setting
and thermostat setting must be the same.
Jumper Settings/Positions for Pump/Boiler On/Off Delay
The pump/boiler on delay and the pump off delay
are fixed at three minutes. The default setting for
the boiler off delay is also three minutes, but can
be changed to 15 minutes. To do this, carefully
remove the jumper and re-insert it in the other
position as shown below:
Note: the red reset button to the right of the
boiler delay jumpers. Using a suitable tool, press
this button at any time to reset the KL08NSB
back to factory default settings.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Salus KL08NSB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Salus KL08NSB in de taal/talen: Engels als bijlage per email.

De handleiding is 3,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info