714753
6
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
6
Assembly
ASSEMBLING THE JUICER
1. Pull the juice press arm up, away from the
motor base, until fully extended.
2. Place the juice collector onto the drive shaft on
top of the motor base, ensuring the juice spout
ts into the semi-circular groove at the front
of the motor base.
3. Insert the lter into the juice collector, aligning
the indent with arrow in the bottom of the lter
over the corresponding tab with arrow in the
juice collector.
4. Place the juicing cone onto the drive shaft and
press down lightly to lock the cone into position.
5. To insert the fruit dome, place it into the hole on
the underside of the juice press arm. The fruit
dome is magnetic and will stick into place.
6. Ensure the anti-drip juice spout is pushed
down into the pouring position.
DISASSEMBLING THE JUICER
1. Turn the juicer OFF at the ON/OFF button,
then unplug from the power outlet.
2. Pull the juice press arm up, away from
the motor base, until fully extended.
Close the anti drip spout by flipping it up.
3. Remove the fruit dome by pulling on it gently
to release the magnet
4. Lift the juice collector from the base with the
lter, juicing cone and fruit dome still in place.
Remove the cone and lter from the juice
collector over a sink for easier cleaning. Follow
recommended care and cleaning guidelines.
Functions
1. Ensure the juicer is correctly assembled and
a glass or jug is placed under the juice spout
before juicing.
2. Cut the citrus fruit in half by cutting across the
fruit segments, rather than across the tip ends,
to ensure more ecient juicing.
3. Plug the power cord into a 220–240V power
outlet, then press ON/OFF switch to ON.
4. Place a citrus fruit half, cut side down,
onto the juice cone and push down lightly
onto the spikes.
5. Grasp the handle and slowly lower the juice
press arm. Press down (in a gentle but rm
action) until the fruit dome is in contact with the
fruit skin. The motor will automatically start and
the juicing cone will begin to rotate. The juice
will be extracted from the fruit and ow through
the juice spout into the glass. The pulp and
seeds will collect in the lter.
6. The juicer juices very quickly so each
fruit half will be juiced in a few seconds.
To automatically stop the motor, lift the juice
press arm up to its extended position.
7. Remove the used fruit from the
juicing cone. Empty excess pulp
and seeds from the lter as required.
Repeat Steps 3–7 to continue juicing.
NOTE
The lter should be emptied when full with pulp
and seeds. The lter can be emptied during juicing
by turning the juicer OFF at the ON/OFF switch
and carefully removing the juicing cone and lter.
Clean and replace lter and juicing cone before
continuing to juice. Do not allow the lter to overll
as this may prevent correct operation or damage
the unit.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Sage-SCP600

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sage SCP600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sage SCP600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info