634236
3
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
INSTALLATION AND OPERATING
INSTRUCTIONS
INTRODUCTION
The Seafarer 5 echo sounder operates by measuring
the time interval between transmission and reception
of ultra-sonic pulses from the sea bed via a piezo
electric transducer fitted in the hull of the boat.
The depth is displayed on a circular dial by a
brilliant yellow Light Emitting Diode (LED) on two
range scales. Ranges are t)-20m and
0-120m on
metric model or 0-&ft and 0-i0 fathoms on Feet/
Fathoms model. In addition. the instrument is fitted
with a depth alarm (audible and visual) which
operates up to 30 metres (16 fathoms).
TRANSDUCER INSTALLATION
WARNING: The co-axial cable is sealed into the
stem of the transducer and if damaged in any way
cannot be reconnected. The transducer lead has a
nominal length of 24 feet (7.3 metres) and should not
be extended or cut without the advice of a service
engineer. Any excess cable should be coiled away
from excessive heat or sources of electrical
i
nterference. Transducers with longer cable can be
supplied to special order. For full depth performance
the transducer stem should he mounted as near
vertical as possible. Install the transducer in a part of
the hull which is as clear as possible from aerated or
Fig. 1
t
urbulent water and where accidental damage is
unlikely to occur. Normally a position slightly aft of
amidships is preferable. For fin-keel sailing boats it
may be preferable to fully recess the transducer into
the stem so that the face is completely flush. It should
be remembered that the beam angle of the
transducer is ±22
1
/2
°
and care should he taken that a
false echo is not created by the keel. If a single
transducer is installed on the centre line of the boat
depth readings will he obtained up to an heel angle of
221/2
°
.
If two transducers arc required, to avoid fin-
keels for instance, then each should be fitted in
opposite bilges facing outward at an angle of
approximately 15
°
.
By using an automatic change-
over switch (optional extra) available from all good
chandlers. a twin transducer installation will enable
the Seafarer 5 and 700 to give accurate depth
readings to an heel angle of 37'/2
°
.
The following illustration indicates typical
transducer installations using a wooden fairing block
outside the hull. The fairing block has been carefully
bored, carved and sanded to a streamlined shape
avoiding the creation of turbulent water which may
reduce or even prevent depth indication when the
boat is travelling at a speed. In one of the examples
shown, an internal fairing block has been used for
strength and sealing and to allow for hull curvature.
The installation should he carefully rendered
watertight by using a sealing compound between all
mating surfaces. Do not over-tighten the nuts on the
transducer stem.
3
Stem Fitting
Bilge
Mounting
Not
to
Scale
Transducer
Head
Embedded
i
n
Mastic
Sealing
Compound
90'
r
Alt
Fore
Level F,umg to Avoid
Water Turbulence
TRANSDUCER INSTALLATION
DIAGRAM
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw SEAFARER 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van SEAFARER 5 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info