513654
7
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
3
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
INSTALLING BITS
See Figure 6 - 7.
Lock the switch trigger by placing the direction of
rotation selector in the center position.
Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend to
use. Also, raise the front of the drill slightly to keep the
bit from falling out of the chuck jaws.
Insert the drill bit.
WARNING
Make sure to insert the drill bit straight into the chuck jaws.
Do not insert the drill bit into the chuck jaws at an angle
then tighten. This could cause the drill bit to be thrown
from the drill, resulting in possible serious personal injury
or damage to the chuck.
Tighten the chuck jaws on the drill bit.
NOTE: Rotate the chuck body in the direction of the arrow
marked LOCK to close the chuck jaws. Do not use a
wrench to tighten or loosen the chuck jaws.
REMOVING BITS
See Figure 6.
Lock the switch trigger by placing the direction of
rotation selector in the center position.
Open the chuck jaws.
NOTE: Rotate the chuck body in the direction of the arrow
marked UNLOCK to open the chuck jaws. Do not use a
wrench to tighten or loosen the chuck jaws.
Remove the drill bit.
TWO-SPEED GEAR SWITCH (HIGH-LOW)
See Figure 9.
A slide switch is located on top of the drill to select either
low (1) or high (2) speed. When using drill in the low (1)
speed range, speed will decrease and unit will have more
power and torque. When using drill in the high (2) speed
range, speed will increase and unit will have less power
and torque. Use low (1) speed for high power and torque
applications and high (2) speed for fast drilling or driving
applications.
ADJUSTABLE TORQUE CLUTCH
See Figure 8.
When using the drill-driver for various driving applications,
it becomes necessary to increase or decrease the torque
in order to help prevent the possibility of damaging screw
heads, threads, workpiece, and so on. In general, torque
intensity should correspond to the screw diameter. If the
torque is too high or the screws too small, the screws may
be damaged or broken.
The torque is adjusted by rotating the torque adjustment
ring. The torque is greater when the torque adjustment
ring is set on a higher setting. The torque is less when the
torque adjustment ring is set on a lower setting.
The proper setting depends on the type of material and the
size of screw you are using.
ADJUSTING TORQUE
Identify the 24 torque indicator settings located on the
front of the drill.
Rotate adjusting ring to the desired setting.
1 - 4 For driving small screws
5 - 8 For driving screws into soft material
9 - 12 For driving screws into soft and hard
materials
13 - 16 For driving screws in hard wood
17 - 20 For driving large screws
21 -
For drilling
DRILLING
Check the direction of rotation selector for the correct
setting (forward or reverse).
Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
Hold the drill firmly and place the bit at the point to
be drilled.
Depress the switch trigger to start the drill.
Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
WARNING
Be prepared for binding at bit breakthrough. When these
situations occur, drill has a tendency to grab and kick
opposite to the direction of rotation and could cause loss
of control when breaking through material. If not prepared,
this loss of control can result in possible serious injury.
When drilling hard, smooth surfaces, use a center
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ryobi LSDT1202 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ryobi LSDT1202 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info