483581
5
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
2
Filling the water tank
Before filling the water tank, unplug from the mains and set the steam
control to the Dry position .
To open the water filling inlet, push the cover downwards, tilt the iron
and pour in untreated tap water up to the maximum level ( ). Close
the cover before holding the iron horizontal again.
What water may be used?
Your iron has been designed to operate using untreated tap water.
However, if your water is very hard, you can mix it 50% tap water with
50% distilled or demineralised water.
Do no add anything to the contents of the water tank and do not use
water from clothes dryers, scented or softened water, water from refri-
gerators, batteries or air conditioners, pure distilled water, rain water,
boiled water, bottled water or filtered water. These contain organic
waste or mineral elements that become concentrated when heated and
cause spitting, brown staining or premature wear to your iron.
Tip: Spray starch onto the reverse side of the fabric to be ironed to
avoid stains on the soleplate.
Setting the temperature
Using the temperature control ( ), set the iron temperature to suit the
type of material. We recommend using the above table as a guide. The
thermostat light ( ) indicates that the soleplate is heating up. When
the light goes out, the required temperature has been reached.
Please note: When heating up the iron from cold, wait until the ther-
mostat light has gone out a second time. Only then is the set
temperature reached.
Tip: We recommend that you start with fabrics to be ironed at a low
temperature as the iron takes longer to cool down than to heat up.
For mixed fabrics set the temperature for the most delicate fabrics.
Ironing and Steam functions
E1 Ironing with Dry Position (without steam)
To iron without continuous steam and for perfect finishing results turn
the steam control ( ) to the Dry Position . It will engage with a
“Click”. Set the temperature to suit the type of material
(care points
, •• or •••).
E2 Steam ironing
You can iron with continuous steam by setting the temperature dial
( ) in the marked steam zone (after
••
). The steam quantity can be set
between minimum (see drawing E2, smallest dot) and maximum
steam . We recommend setting to maximum steam quantity only
when the iron is at maximum temperature setting to avoid droplets of
water leaking from the soleplate.
E3 Extra Long Shot button (temperature setting at maximum)
Your iron is equipped with a new special Extra Long Shot, which
allows you to iron out creases perfectly, specifically on dry and thick
fabrics. By pressing the Extra Long Shot button ( ) steam is pushed
with more pressure into the fabrics, because of this new technology.
The steam reaches a bigger area and penetrates much deeper into
fabrics. So you get excellent results from your ironing.
The pressure generated may cause a slight noise. This is not a
technical fault!
The Extra Long Shot (E3) is also possible to use if the steam control is
set to the Dry Position .
Ironing label Fabric
Synthetic fibres e.g.
viscose, polyester
silk, wool
cotton, linen
Temperature control
C
D
E
DX8000-7spr 21.10.2004 10:29 Uhr Seite 2
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rowenta DX8300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rowenta DX8300 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info