489974
9
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
9
English
conductor. Be careful not to cut into the wire strands. Unscrew (turn
counterclockwise) the speaker connector collar. Place the connector
lug around the shaft, or insert the bundled wire into the hole in the
shaft. Turn the collars clockwise to clamp the connector lug or wire
firmly in place.
For each group of channels, connect the left speaker to the pair of
speaker connectors labeled LEFT. Connect the right speaker to the
speaker connectors labeled RIGHT. Follow the labels printed above
the connectors. Make sure that the positive terminal of the speaker
is connected to the + terminal on the amplifier. Make sure that the
negative terminal of the speaker is connected to the terminal of the
amplifier.
Note: Be sure there are no loose wire strands that could touch
adjacent wires or connectors
Plug connection
8
Connect your speaker wires as shown in the illustration. Insert the wire
into the open and turn the screw to clamp the wire in place.
Be sure to keep the polarity of the connections correct.
Speaker Selection
The nominal impedance of the loudspeaker(s) connected to the RMB-
1512 should be a minimum of 4 ohms. When driving multiple pairs of
speakers connected in parallel, the effective impedance the amplifier
sees is cut in half. For example, when driving two pair of 8 ohm
speakers, the amplifier sees a 4 ohm load. When driving multiple
speakers in parallel, select speakers with a nominal impedance of 8
ohms or higher.
Speaker Wire Selection
Use insulated two-conductor stranded wire to connect the RMB-1512
to the speakers. The size and quality of the wire can have an audible
effect on the performance of the system. Standard speaker wire will
work, but can result in lower output or diminished bass response,
particularly over longer distances. In general, heavier wire will
improve the sound. For best performance, you may want to consider
special high-quality speaker cables.Your authorized Rotel dealer can
help in the selection of cables for your system.
Polarity and Phasing
The polarity or positive/negative orientation of the connections for
every speaker and amplifier connection must be consistent so all
the speakers will be in phase. If the polarity of one connection is
mistakenly reversed, bass output will be very weak and stereo imaging
degraded. All wire is marked so you can identify the two conductors.
There may be ribs or a stripe on the insulation of one conductor. The
wire may have clear insulation with different color conductors (copper
and silver). There may be polarity indications printed on the insulation.
Identify the positive and negative conductors and be consistent with
every speaker and amplifier connection.
Speaker Wire Connection
6
See Figure 2
Route the wires from the RMB-1512 to the speakers. Give yourself
enough slack so you can move the components to allow access to the
speaker connectors.
The RMB-1512 has two pair of color-coded speaker connectors for
each group of amplifier channels, one for the left speaker, the other
for the right speaker. Labels above the connectors show the proper
connections for connecting speakers. These speaker connectors accept
bare wire, connector lugs, or “banana” type connectors (except in the
European Community countries where there use is not permitted).
The RMB-1512 also has a plug-in speaker connector that can make
connection easier in custom installations. You can pre-wire the plug-in
connector before the amplifier is installed. The plug-in connector is
wires in parallel with the bind post outputs.
Note: The following text describes both binding post and plug-in
connections. DO NOT use both connection methods in combination to
connect multiple speakers.
Binding Post connection
6
If you are using banana plugs, connect them to the wires and then
plug into the backs of the binding posts. The collars of the speaker
connectors should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are
attaching bare wires directly to the speaker connectors, separate the
wire conductors and strip back the insulation from the end of each
R+
R--
L--
L+
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rotel RMB-1512 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rotel RMB-1512 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info