577720
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
9
Connections
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.
Front USB Input
2
See figure 5
The front USB input can be connected to an iPod, iPhone, USB flash memory
or the Bluetooth dongle (supplied) for wireless streaming. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.
Bluetooth Connection
See figure 5
Insert the supplied Bluetooth Dongle into the front USB for wireless streaming
via Bluetooth, from your device (i.e. mobile phones) to the RDD-1580. From
your mobile device, look for „Rotel Bluetooth‰ and connect to it. Connection
is normally automatic, but if prompted for a password, please press „0000‰
on your device.
NOTE: Not all Bluetooth dongles will operate with RDD-1580. Please
use the one supplied.
Analog Outputs
6
See figure 3 and figure 4
A pair of standard RCA jacks and XLR balanced connectors supplies an
analog output signal from the RDD-1580 to the source inputs of an audio
preamplifier, integrated amplifier, or receiver.
NOTE: You should choose only one method of analog connection from
the RDD-1580. Do not connect both the RCA and XLR at the same time.
Select high quality audio interconnect cables. Connect the left and right
channel outputs of the RDD-1580 to the corresponding inputs on the
preamplifier or other component.
Digital Inputs
7
See figure 3
There are two sets of digital inputs labeled COAX 1 and 2, OPT 1 and 2.
Connect the COAXIAL or OPTICAL PCM outputs of your source component
into these sockets. The digital signals will be decoded and played by the RDD-
1580. The unit is capable of decoding PCM signals up to 24 bit, 192kHZ.
PC-USB Input
7
See figure 3
Connect this input using the supplied USB cable to the USB socket of your
computer.
The RDD-1580 supports both USB Audio Class1.0 and USB Audio Class 2.0
modes. Windows computers do not require installation of a driver for USB
Audio Class 1.0 and supports playback of audio up to 96KHz sampling
rates. The Factory Default setting is USB Audio Class 1.0.
To take advantage of USB Audio Class 2.0 audio playback supporting
up to 192KHz sampling rates you will need to install the Windows driver
supplied on CD included with the RDD-1580. You will also need to switch
the RDD-1580 to USB Audio Class 2.0 playback mode with the following:
1. Press and Hold the PC-USB source button on the front panel for 5 seconds.
The current USB audio mode is indicated by the blinking Sample Rate LED as:
USB Audio Class 1.0 ă Sample Rate 96KHz blinking [Factory Default]
USB Audio Class 2.0 ă Sample Rate 192KHz blinking
2. Press the PC-USB key again to illuminate the 192K sample rate light blinks.
3. Pressing the PC-USB key will toggle between USB Audio Class 1.0 (96KHz
light blinks) and USB Audio Class 2.0 (192KHz light blinks).
4. After the desired USB Audio mode is selected wait 3 seconds for the
selection period to end and the RDD-1580 will use the selected audio mode.
5. Power cycle the RDD-1580 and your PC after changing the USB Audio
mode to ensure both units are properly configured.
Many audio playback applications do not support 192KHz sampling rate.
Please confirm your audio player supports 192KHz audio and you have
192KHz audio files to properly playback this sample rate. Also, you may
need to configure the audio driver in your PC to output 192KHz or your
computer may „down sample‰ to a lower audio sample rate. For more
information please refer to your audio player or operating system information.
NOTE: USB Audio Class 2.0 required installation of the Windows PC
driver on the CD ROM included with the RDD-1580. MAC computers do
not require a driver to support PC-USB 1.0 or 2.0 audio.
NOTE: Upon successful installation of the driver, you may need to select
the ROTEL audio driver from the audio/speaker setup of your computer.
Computer I/O Connector
8
The RDD-1580 can be controlled via RS232 for integration with automation
systems. The COMPUTER I/O input accepts a standard straight DB-9 Male-
to-Female cable.
For additional information on the connections, software, and operating codes
for computer control of the RDD-1580, contact your authorized Rotel dealer.
ROTEL LINK
9
This 3.5 mm stereo mini-jack (labeled ROTEL LINK IN) can optionally attach
to Rotel network enabled products with ROTEL LINK OUT connections. This
allows the attached Rotel products to communicate with each other and
be controlled via the Rotel Remote App (available for download on the
iTunes
®
store).
EXT REM IN Jack
0
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when
the unit is installed in a cabinet and the front-panel sensor is blocked. Consult
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rotel RDD-1580 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rotel RDD-1580 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info