714264
29
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
29
Important information on working with your oil press
Use only seeds and nuts with a high oil content.
The raw material to be processed must not be larger than peanuts resp. hazelnuts. If necessary,
crush them to ensure optimum processing. To do so, use a mincing knife, for example. Also very small
particles might block the screw conveyor, like e.g. nut crumbs or nut dust, groats or seed powder, which
is produced when pre-treating nuts/seeds in a grinder or blender. In this case we recommend to sieve
the smallest particles before pressing.
Before filling in the material to be pressed, pay attention that it does not contain foreign matters such
as small stones etc.
The seeds and nuts to be processed must be sufficiently dried. We recommend to dry them prior to
processing at 60 °C (circulating air) to 80 °C (upper and lower heat) for 2 to 3 hours in the oven to
achieve an optimum oil yield. In ideal circumstances fill in the seeds/nuts when they are still warm. For
storage – also short-term – pack seeds/nuts airtight.
TIP: Start processing with a small amount to test the quality and the moisture content.
TIP: Walnuts are a real hardness test. Ideally use walnuts which have been dried a very long time
(e.g. in a dehydrator, at 50 °C for 24 hours) or nuts from the previous season.
The appliance is not designed for pressing soya beans or olives.
Error Cause and troubleshooting
Appliance cannot be
switch on.
Check whether the locking mechanism is correctly locked.
Check whether the appliance is correctly plugged in.
Test the socket by connecting another appliance.
Check whether the power cord or the plug is damaged.
- If they are damaged, do not use the appliance.
The appliance is heating-up.
- The pilot lamp flashes or is permanently illuminated in red during heating-up.
Check if the appliance is assembled correctly.
- If necessary, disassemble and re-assemble the appliance.
Check whether the lid is correctly seated on the seed container.
- Press the lid firmly.
Check whether the micro switch at the rear (back upper edge) is clogged.
- Clean the micro switch.
If the appliance has been used too long, the overheating protection of the
motor is activated.
- Allow the appliance to cool down.
The appliance stops
during operation.
Check whether the material which has been filled in (too large, too hard or
too moist) blocks the screw conveyor.
- Clear the blockage. (see section on “Clearing an screw conveyor blockage”).
• Seed container empty. There is not sufficient material in the screw conveyor.
The appliance stops automatically after 1 minute.
- Check if there is sufficient material in the hopper or if it is jammed. Refill
if necessary and restart the appliance.
Check whether the lid is correctly seated on the seed container.
- Press the lid firmly.
If the appliance has been used too long, the overheating protection of the
motor is activated.
- Allow the appliance to cool down.
Trouble shooting
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rommelsbacher OP700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rommelsbacher OP700 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info