714011
37
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
37
Error codes
The electronic control features several internal monitoring functions.
If an error occurs, the power supply will be switched-off and an error code will appear on the display. In
addition, there is a signal tone during the first 60 seconds.
Error code table:
E0 Pot recognition: Each cooking zone features a sensor, which recognizes whether there is a
vessel on the cooking zone. If no suitable vessel is recognized on the cooking zone after switch-
on, the display will show “E0”.
Self-help: Place a pot on the cooking zone within 60 seconds; otherwise the electronics will
switch the unit into the “Standby” mode. (Also refer to point “Getting acquainted with your
appliance“)
E1 Electronic error: A short-circuit has occurred in an electronic circuit of the appliance.
Self-help: Not possible – the appliance must be forwarded to the customer service at any rate.
E2 Temperature sensor: The temperature sensor below the glass ceramic plate provides an undue
value.
Self-help: Allow the appliance to stand for a while in order to adjust to the ambient temperature.
E3 Electronic control of over-voltage: An Error has occurred in an electronic circuit of the
appliance due to excessively high voltage (> 270 V~).
Self-help: Make sure the appliance is connected to the voltage indicated on the rating label.
E4 Electronic control of under-voltage: An error has occurred in an electronic circuit of the
appliance due to excessively low voltage (< 160 V~).
Self-help: Make sure the appliance is connected to the voltage indicated on the rating label.
E5 Overheating protection (“power level” mode): During the “power level” mode the
temperature on the cooktop exceeds the maximum tolerable value of 200 °C (e.g. due to hot oil
or fat or an empty pot or any other metal object while the appliance is switched on).
Self-help: Eliminate the cause of overheating. Once the cooktop has cooled, the appliance
can be put into operation again. Afterwards, use the “temperature level” mode for constant
temperatures above 200 °C.
E6 Inside temperature: The inside of the appliance is too warm (e.g. due to hindered air supply,
blocked or defective fan or excessive ambient temperature).
Self-help: Clean the ventilation holes or remove any impurities that might be there, improve the
ventilation.
NOTE: For all displayed error codes, except of “E0”, it is necessary to manually reset the
control by pulling the power plug or separating the unit from the power supply.
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rommelsbacher CT2020IN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rommelsbacher CT2020IN in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info