167811
24
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
4. CROSSOVER SETTINGS
24
4.2.2 BANDPASS FOR KICKBASS
SYSTEMS
If you intend to operate a kickbass loudspeaker system in the
front doors of your vehicle, you must select two crossover
frequencies at the active crossover of your RODEK amplifier.
The operation mode of the channel pair driving the kickbass
speaker system must be set to BP (bandpass). The bandpass
filter contains a highpass (10 - 400Hz) with a cascaded lowpass
(30 - 400Hz) filter. The lowpass crossover point is usually set at
a frequency that equals at least twice the value of the highpass
crossover frequency setting. The lowpass filter frequency is
mostly set a little lower, than the highpass crossover frequency
of the satellite channels.
Kickbass speaker system, front door mounted, recommended
bandpass frequencies
16 cm Kickbass Speaker System 80 - 110 Hz Highpass
200 - 250 Hz Lowpass
4.2.3 BANDPASS FOR SUBWOOFER
SYSTEMS
To drive a subwoofer system, the integrated electronic cross-
over of the channels CH5/6 must also operate in bandpass mode.
Before you attempt to adjust the lowpass crossover frequency,
you must first turn the (subsonic)highpass frequency control
counterclockwise to its lowest position at 10 Hz.
Now you can set an appropriate lowpass crossover frequency.
For this purpose, open the input gain control - the arrow of the
knob should point to "noon" - so you can hear the subwoofer
playing. Ideally, the low-pass cut-off frequency should be set
between 50 to 90 Hz - and this setting has to be entirely deter-
mined by ear. Try to find lowpass crossover frequency setting,
that gives you a "full-bodied" bass reproduction with enough
impact in the upper bass range.
Note: If the lowpass crossover frequency is set too low, the
sound will have a tendency to sound extremely soft and low-
end heavy!
Now you can adjust the subsonic-highpass, if you wish to
squeeze out the most (max-dB) of your subwoofer system.
Turn the highpass frequency control up, to a point where you
can hear that the bass reproduction starts to get "thinner".
The subsonic highpass frequency should be set to a value
between 20 to maximum 50 Hz.
R680A2 Manual_E+D.indd 24R680A2 Manual_E+D.indd 24 07.07.2004 12:36:46 Uhr07.07.2004 12:36:46 Uhr
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 680 a 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 680 a 2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info