166582
27
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
27
4.1 MINIMUM IMPEDANCE LOAD
The output stages of the RODEK amplifiers are designed
to give you extraordinary output power into 4 or 2 ohms
loads in normal stereo configurations. In bridged mode,
the minimum impedance load is 4 ohms. The amplifier
might suffer from thermal shut-down or even damage, if
these recommended minimum impedance load ratings
are not considered appropriately. The R1500A2 is stable
into 2 ohms.
4.2 SELECTING THE OPERATION MODE
The RODEK amplifiers feature an active crossover sec-
tion with full versatility and thus, offer different amplifi-
cation modes, which can be set by the operation mode
slide switch(es). The operation mode switch enables you
to configure each stereo channel pair to work in either
fullrange, highpass or even bandpass mode. Therefore
- before you get started with the settings of crossover
frequencies and input gain adjustments - you must se-
lect the appropriate operation mode for each channel
pair, depending on the speaker system that is connected
and driven by the amplifier. This will make sure that every
speaker system is only working in its proper frequency
operation range, for which the speaker was designed.
For example select HIGHPASS, if the speaker is a com-
ponent- or coaxial type, or BANDPASS in case of a kick-
bass or subwoofer system - and finally FULL(range) if
the passband frequency of the stereo channel is already
controlled by a head-unit with an integrated DSP based
active crossover.
4.2.1 HIGHPASS FOR COMPONENT
AND COAXIAL SPEAKERS
Before you start your adjustments, all tone controls (i.e.
Bass, Treble), fader/balance and the loudness function
featured on the head unit, must be set to their respective
neutral or center position.
Please take a look at the chart below, stating the recom-
mended high-pass cross-over frequency settings for
coaxial- and component speaker systems - and adjust the
highpass control of each channel pair that drives satel-
lites speaker systems accordingly. The most important
factor for the individual adjustment of the highpass cross-
over frequency is the reproduction of mid-bass frequen-
cies and the resulting power-handling of the speaker
system. This setting is always a compromise. Try to find
a highpass crossover frequency point, that will suit your
personal listening preferences and - at the same time -
also considers the physical (cone excursion) capabilities
of your speakers best.
Satellite speaker system, front door mounted, recom-
mended highpass frequency
10 cm Coaxial- or Component System 90 - 120 Hz
13 cm Coaxial- or Component System 80 - 100 Hz
16 cm Coaxial- or Component System 60 - 90 Hz
Satellite speaker system, rear mounted, recommended
highpass frequency
10 cm Coaxial- or Component System 100 - 150 Hz
13 cm Coaxial- or Component System 120 - 150 Hz
16 cm Coaxial- or Component System 130 - 150 Hz
4. CROSSOVER SETTINGS
R1500-4100A2 Manual.indd 27R1500-4100A2 Manual.indd 27 07.07.2004 10:59:11 Uhr07.07.2004 10:59:11 Uhr
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 2180 i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 2180 i in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info