66481
5
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
5
DESIGN FEATURES
INSTALLATION
INSTALLATION CONSIDERATIONS
The following is a list of tools needed for installation:
Volt/Ohm Meter
Wire strippers
Wire crimpers
Wire cutters
#2 Phillips screwdriver
Battery post wrench
Hand held drill w/assorted bits
1/8" diameter heatshrink tubing
Assorted connectors
Adequate Length—Red Power Wire
Adequate Length—Remote Turn-on Wire
Adequate Length—Black Grounding Wire
7. Remote Bass The Para-Punch Remote Bass connection is made with a RJ-45 cable and can be installed
in a variety of ways for easy control access.One control is used to boost low frequency information to
overcome road noise and put the bass in your face.This Bass control is a narrow band adjustment
variable from 0dB to +18dB with a Gyrator based Punch EQ that eliminates frequency shift with boost.
The other control is used for adjusting center frequency variable from 35Hz to 70Hz.
8. Infrasonic Filter A 28Hz High Pass filter designed to prevent frequencies below the audio range
from being applied to the subwoofer from the amplifier. Consequently improving subwoofer
performance and power handling, particularly in vented enclosures.
9. Gain Control The input gain control is preset to match the output of most source units. It can be
adjusted to match output levels from a variety of source units.
10. Variable Crossover Is a built-in adjustable filter selectable for High-Pass (HP),All Pass (AP),or
Low-Pass (LP) operation variable from 40Hz to 400Hz in x1 mode, and 400-4000Hz in x10 mode.
11. Frequency Multiply Switch Used to set the multiplier for the crossover frequencies between x1
and x10.A setting of x1 leaves the adjustable crossover frequency from 40-400Hz.A setting of x10
changes the adjustable crossover frequency to 400-4000Hz
12. Slope Switch – Used to select between a 12dB/octave Butterworth or 24dB/octave Linkwitz-Riley
filter.
13. RCA Input Jacks The industry standard RCA jacks provide an easy connection for signal level input.
They are nickel-plated to resist the signal degradation caused by corrosion.
14. RCA Active Pass-Thru Jacks This Active Pass-Thru provides a convenient source for daisy-chaining
an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the
rear amplifier location.
15. Preamp Output Crossover – Is used to set the crossover output for the Pass-Thru Jacks
selectable for High-Pass (HP),All Pass (AP), or Low-Pass (LP) operation. If set to HP or LP the
frequency of th Pass-Thru outputs will be the same frequency selected for the main crossover.
16. Remote Terminal This heavy duty, platinum-plated wire connector will accept wire sizes from
12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when
+12V DC is applied.
17.
Power Terminals The power and ground connectors on the amplifier are platinum-plated and will
accommodate up to 1/0 AWG wire maximizing the input current capability of the amplifier.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rockford Fosgate T8002 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rockford Fosgate T8002 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info