320729
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
1.CARREGUE A BOLA ROBÓTICA DURANTE
3-5 HORAS (Ver a foto A).
2. COLOQUE UM PANO DE MICROFIBRA ELECTROESTÁTICA
3. COLOQUE A ARMÃO NO MEIO DA ÁREA A LIMPAR
4. SELECIONE O TEMPO DE LIMPEZA
Pressione o botão verde ON/TIME. (Ver foto E).
5.COLOQUE A BOLA ROBÓTICA DENTRO DA ARMAÇÃO
Alguns segundos depois o RoboMop começara a limpeza.
6.PARAGEM AUTOMÁTICA (Ver foto G).
7. PANOS DE MICROFIBRAS ELECTROESTÁTICAS
DESCARTÁVEIS. Não deite os panos na sanita. (Ver foto H).
COMO ENCOMENDAR PANOS ADICIONAIS DE
MICROFIBRAS ELECTROESTÁTICAS: Visite a nossa
página na net em: www.robomop.pt
OPERATOR`S MANUAL
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has
been designed to fit under the kickboards in your
kitchen. If your bed or furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has
been designed to fit under the kickboards in your
kitchen. If your bed or furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
x1
x5
x1
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on
the floor: clothing, loose papers, pull cords for blinds or curtains, power cords,
or any fragile items. RoboMop contacts walls, furniture and other objects as
it cleans, so please remove any items that may be pushed and knocked over
by light contact from RoboMop. If your room does not have a door, or there is
access to a stairway where RoboMop can fall down the stairs, simply block off
the area with either a chair, plant, gate or other object.
1. CHARGE THE ROBOTIC BALL
FOR 3-5 HOURS (Fig. A).
2. ATTACH ONE ELECTROSTATIC PAD (Fig.C).
3. PLACE THE CLEANING FRAME IN THE
CENTER OF THE ROOM (Fig.D).
4. SELECT CLEANING TIME
by pressing the Green ON/TIME button (Fig.E).
5. INSERT THE ROBOTIC BALL IN THE CLEANING FRAME
Within seconds, RoboMop will begin cleaning. (Fig.F).
6. ROBOMOP WILL AUTOMATICALLY SHUT
OFF WHEN THE PROGRAM IS COMPLETE (Fig.G).
7. DISPOSE THE PAD IN THE GARBAGE AFTER USE (Fig.H)
Do not dispose soiled pads in the toilet.
REPLACEMENT ELECTROSTATIC PADS:
Available online at www.robomop.net and at retailers everywhere.
5.INDSÆT ROBOT KUGLEN I MOPPEHOVEDET
Indenfor 6 sekunder, RoboMop vil automatisk starte rengøringen
6.SLUKKER AUTOMATISK (Figur G).
7. BORTSKAFFELSE AF ENGANGS KLUDE. Brugte klude
smides i affalds spanden (Figur H).Må ikke smides i toilettet.
ELEKTROSTATISKE KLUDE KAN KØBES I
DETAILHANDLEN. Besøg vor hjemmeside
www.armanitrading.dk
1.LADE DEN ROBOTISKE BALLEN I 3-5 TIMER
(Figur A).
2. PÅMONTER DET ELEKTROSTATISKE PAPIRET (Figur C).
3. PLASSER ROBOMOP RAMMEN I MIDTEN AV ROMMET
(Figur D).
4.VELG RENGJØRINGSTID. Trykk på den grønne ON/TIME
knappen. (Figur E).
5.PLASSER DEN ROBOTISKE BALLEN I
RENGJØRINGSRAMMEN. Innen noen sekunder vil
Robomop begynne å rengjøre. (Figur F).
6.SLÅR SEG AV AUTOMATISK (Figur G).
7. FJERNING AV PAPIRET (ikke kast papiret i toalettet). (Figur H).
ELEKTROSTATISKE PAPIRET KAN
BESTILLES PÅ: www.robomop.net
GEBRUIKSAANWIJZING
MANUAL DE INSTRUÇÕES
INSTRUKSJONSMANUAL
WARNINGS: • Charge the robotic ball only when it is completely discharged. • Do not use
RoboMop on wet or damp surfaces or where immersion in water is a possibility. • Out of reach of
children. • Plug the AC Battery Charger into a voltage tape AC Outlet Only and according to the
adapter specications • Use only the AC Battery charger supplied by the manufacturer. • Charge
indoors only. • Always remove AC Battery Charger from wall and disconnect RoboMop after
charging. • RoboMop is not for use on carpets.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
Figure G
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transpor t the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transpor t the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transpor t the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transpor t the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transpor t the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
Figure E
Figure G
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
Figure E
Figure G
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
Figure E
Figure G
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
Figure E
Figure G
ADVARSEL: • Genoplad kun robot hovdet når det er helt aadet. • Må ikke anvendes på våde
overader, eller hvor den kan komme i forbindelse med vand. • Benyt kun den medfølgende
batteri oplader til opladning, anvendelse af andre opladere kan skade robot kuglen. • Opbevares
utilgængeligt for børn. • Må kun genoplades indendørs. • Batteri opladeren må ikke blive våd.
Hav altid tørre hænder når du benytter opladeren. • RoboMop kan ikke benyttes på gulvtæpper.
WAARSCHUWINGEN: • Laad de robotbal enkel op wanneer de batterij volledig leeg is.
• Gebruik de RoboMop niet op natte of vochtige oppervlakken of waar de RoboMop in water
kan worden ondergedompeld. • Bewaar de RoboMop buiten bereik van kinderen. • Sluit de AC
batterijlader enkel aan op een AC stopcontact. Het toestel mag niet worden gebruikt met eender
welke stroomomzetter. • Gebruik enkel de AC batterijlader die door de fabrikant is geleverd om
het toestel te laden en te ontladen. • Laad het toestel enkel binnenshuis op. • Haal de AC
batterijlader altijd uit het stopcontact en schakel de RoboMop uit na het laden.
• De RoboMop is niet geschikt voor tapijten.
OBSERVERE:• Oppbevares utilgjengelig for barn. • Lad bare den elektroniske ballen etter at
batteriet er helt utladet. • Benytt aldri RoboMop på våte eller fuktige ater eller der det er en risiko
for at det kan forekomme vann.• Strømpluggen skal kun benyttes med 220Volts uttak. Produktet
skal aldribrukes med andre typer transformatorer da dette ikke dekkes av garantien.• Benytt aldri
batteriladeren når du er våt på hendene. • Rammen rengjøres med støvsuger eller tørr klut.
x1 x5
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more impor tant things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dir ty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor sur faces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
x1
x1 x5
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has
been designed to fit under the kickboards in your
kitchen. If your bed or furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more impor tant things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dir ty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor sur faces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more impor tant things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dir ty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor sur faces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
x1
x1 x5
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more impor tant things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dir ty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor sur faces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
x1
1.LAAD DE ROBOTBAL 3-5 UUR OP (Zie fig. A).
2. BEVESTIG EEN ELEKTROSTATISCHE PAD
(Zie fig. C).
3. PLAATS HET POETSFRAME IN HET MIDDEN VAN
DE RUIMTE (Zie fig. D).
4.STEL DE POETSTIJD IN
Druk op de groene ON/TIME toets op de RoboMop, links
onder het LCD-scherm (Zie fig. E).
5.PLAATS DE ROBOTBAL IN HET POETSFRAME (Zie fig. F).
Na zes seconden start de Robomop automatisch.
6.AUTOMATISCH UITSCHAKELEN (Zie fig. G).
7. PADS WEGWERPEN (Zie fig. H).
Gooi de vuile pads niet in het toilet.
HOE EXTRA ELEKTROSTATISCHE PADS BESTELLEN:
Via naar onze website www.robomop.net
AVISOS: • Carregue a bola robótica somente quando esta estiver completamente
descarregada. • Não use o RoboMop em pavimentos molhados ou húmidos ou aonde haja a
possibilidade de imersão em água. • Fora do alcance de crianças. • Conecte o carregador de bateria
unicamente numa tomada de 220 Vlts de acordo com as suas especicações. • Utilize unicamente o
carregador fornecido pelo fabricante. • Carregue somente em espaço interior. • Depois de efectuada a
carga, desligue sempre o carregador de bateria da tomada e do RoboMop. • O RoboMop não pode ser
utilizado em superfícies têxteis (alcatifas, tapetes, carpetes, etc.)
4.ΕΠΙΛΟΓΗ ΧΡΟΝΟΥ ΚΑΘΑΡΙΣΜΟΥ (Δείτε Εικόνα E).
5.ΤΟΠΟΘΕΤΗΣΤΕ ΤΗΝ ΡΟΜΠΟΤΙΚΗ ΜΠΑΛΑ
ΜΕΣΑ ΣΤΟ ΤΕΛΑΡΟ ΚΑΘΑΡΙΣΜΟΥ (Δείτε Εικόνα Z).
6.ΑΥΤΟΜΑΤΟ ΣΤΑΜΑΤΗΜΑ (Δείτε Εικόνα H).
7. ΧΡΗΣΙΜΟΠΟΙΗΜΕΝΑ ΠΑΝΙΑ ΚΑΘΑΡΙΣΜΟΥ
(Δείτε Εικόνα Θ).
Αναλώσιμα ηλεκτροστατικά πανιά:
Μέσω Internet στην σελίδα μας
www.robomop.gr και στα καταστήματα
της περιοχής σας.
1.ΦΟΡΤΙΣΤΕ ΤΗ ΡΟΜΠΟΤΙΚΗ ΜΠΑΛΑ
ΓΙΑ 3-5 ΩΡΕΣ (Δείτε Εικόνα Α).
2. ΤΟΠΟΘΕΤΗΣΤΕ ΕΝΑ ΗΛΕΚΤΡΟΣΤΑΤΙΚΟ
ΠΑΝΙ (Δείτε Εικόνα Γ).
3. ΤΟΠΟΘΕΤΗΣΤΕ ΤΟ ΤΕΛΑΡΟ ΚΑΘΑΡΙΣΜΟΥ
ΣΤΟ ΚΕΝΤΡΟ ΤΟΥ ΔΩΜΑΤΙΟΥ (Δείτε Εικόνα Δ).
ΟΔΗΓΙΕΣ ΧΡΗΣΕΩΣ
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more important things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dirty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor surfaces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transpor t the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
4
step
5
step
7
step
STEP BY STEP GUIDE:
WARNINGS:
Read all safety and operating instructions before operating RoboMop.
Retain the safety and operating instructions for future reference.
Always be careful when using your RoboMop. To reduce the risk
of injury or damage, keep these safety precautions in mind when
setting up, using and maintaining your equipment.
RoboMop must not be used for any other purpose other than its
intended use.
Store out of reach of children.
Do not bend the Cleaning Frame.
Charge the robotic ball only when it is completely discharged.
This is an indoor device only.
Do not use RoboMop on wet or damp surfaces or where immersion
in water is a possibility.
Operate your RoboMop only from the type of power source indicated
in this manual. If you are not sure of the type of power supplied to
your home, consult your local power company.
Plug the AC Battery Charger into a voltage tape AC OUTLET ONLY.
Product may not be used with any type of power converter.
Any such use will immediately void the Warranty.
Use only the AC Battery Charger supplied by the manufacturer
to charge and recharge
this device.
Charge indoors only.
Never handle the AC Battery Charger with wet hands.
Always remove AC Battery Charger from wall and disconnect
RoboMop after charging.
RoboMop is not for use on carpets.
RoboMop is designed to clean one room at a time. Confine
RoboMop to the room you want cleaned by closing all doors.
Observe RoboMop the first time it cleans a room to confirm it does
not get wedged under or stuck on top of uneven surfaces.
The Cleaning Frame should not be washed. Clean softly with a
duster or clean with a dry soft cloth.
Use the specifically designed electrostatic pads on dry floors only.
Protect the Cleaning Frame from bending, warping or folding.
When RoboMop is finished cleaning, remove RoboMop from the floor
to avoid tripping over it.
INSERT THE ROBOTIC BALL
IN THE CLEANING FRAME
Place the RoboMop ball into the
center of the Cleaning Frame.
Within 6 seconds, the RoboMop
will turn itself on automatically.
(See Figure F)
DISPOSAL OF PADS
Dispose soiled pads in the trash .
(See Figure H) Do not dispose
soiled pads in the toilet.
AUTOMATIC SHUT OFF
RoboMop will automatically shut
off when the program is complete,
based on the time you set it to. To
stop the RoboMop at any time,
simply press the Red OFF button.
When RoboMop is finished clean-
ing, remove it from the floor
to avoid tripping or falling over it.
(See Figure G)
6
step
Figure E
Figure F
Figure G
Figure H
54
SELECT CLEANING TIME
Press the Green ON/TIME button
located on your RoboMop under
the LCD screen on the left.
(See Figure E) The LCD display
screen will show the amount of
time the RoboMop will clean your
floor. To choose 1 hour and 30
minutes, press the ON/TIME but-
ton once. To choose 1 hour, press
the ON/TIME button twice. To
choose 30 minutes, press the
ON/TIME button three times.
Once you have chosen the time,
the ON/TIME button on the LCD
screen will flash 6X before turning
on automatically, allowing you
sufficient time to place the ball in
the Cleaning Frame.
x1 x5
OPERATOR’S MANUAL
FREQUENTLY ASKED QUESTIONS:
THIS SET INCLUDES THE FOLLOWING PARTS:
1 Cleaning Frame and 1 Robotic Ball
NOTE:
Read all safety and operating
instructions before operating
your new RoboMop.
1AC Battery Charger
8 Electrostatic Disposable Cloths
2
7
Q. My RoboMop gets stuck. What should I do?
A. Your RoboMop may occasionally get stuck, especially in rooms that
it has not cleaned before. If it does get stuck, RoboMop will try to free
itself by turning in different directions. If it cannot free itself, move or
block any object that RoboMop gets stuck on or under. Once the
problem areas have been amended, pick up your RoboMop and
reposition. Your RoboMop might get stuck for several reasons.
1. It is wedged or pinned between or under narrowly spaced objects.
2. RoboMop bumps into objects and repositions them in such a way
that an exit path no longer exists.
Q. My RoboMop Cleaning Frame has broken. What shall I do?
A. Please contact the local distributor through www.robomop.net.
Q. Are pets and children safe around RoboMop?
A. Children and pets should always be supervised around RoboMop for
optimal safety and cleaning performance.
Q. Does RoboMop clean corners and along the walls?
A. RoboMop cleans next to walls, most corners and other tough to
reach places.
Q. Will it go under kickboards, beds, and furniture?
A. RoboMop has been designed to fit under the kickboards in your
kitchen. If your bed or
furniture is more than 8 cm off the floor, your
RoboMop will happily clean underneath.
Q. How long does it take to recharge the RoboMop?
A. Approximately 3-5 hours.
Q: Will RoboMop clean all floor surfaces?
A: RoboMop cleans hardwood, linoleum, tile, ceramic tile, marble,
granite and other hard floor surfaces.
5
RoboMop is designed to sweep the floors for you so you will have extra time to take care of
more impor tant things or just sit back and relax. Simply attach an electrostatic and dust
absorbing pad, set the cleaning time on the robotic ball, place it in the cleaning frame and
watch RoboMop automatically sweep your floors. Using smart sensor technology, RoboMop
navigates smoothly and silently, cleaning dir ty edges under the kitchen counter, in corners,
around walls and under furniture. The flexible edges will not damage furniture. It is great for
all your hard floor sur faces like wood floors, ceramic tile, granite, marble, and linoleum.
The VoltaWebTM dustpads are especially designed to attract and retain as much dust as
possible during the cleaning session. The dust attraction is obtained through the unique
composition of fibres in the cloth that generates static electricity though friction between the
pad and the floor surface. The pad itself is designed with microscopic dust pockets that
absorb and transport the dust into the centre of the textile. In this way it is possible for the
textile to attract even more dirt. When the pad is soiled, just remove it and toss it in the
trash.
Enjoy your RoboMop!
x1
ΠΡΟΣΟΧΉ: • Φορτίστε την ρομποτική μπάλα μόνο όταν είναι τελείως άδεια.
• Μην χρησιμοποιείτε το Robomop σε βρεγμένες επιφάνειες η όπου υπάρχει
η πιθανότητα νερού. • Κρατήστε το μακριά από παιδιά. • Τοποθετήστε τον
φορτιστή μπαταρίας στην κανονική ηλεκτρική πρίζα 220V. • Χρησιμοποιήστε
μόνο τον φορτιστή που προμηθευτήκατε από το εργοστάσιο. • Φορτίστε την
μπαταρία μόνο μέσα στο σπίτι. • Αποσυνδέστε τον φορτιστή από την πρίζα
μετά την φόρτωση. • Το Robomop δεν χρησιμοποιείτε σε χαλιά.
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
CHARGE THE ROBOTIC
BALL FOR 3-5 HOURS
Before initial use, charge the ball.
Insert the plug of the AC Battery
Charger into the Charger Port
jack of the Robotic Ball.
(See Figure A) Plug the AC
Battery Charger into a voltage tape
AC Outlet ONLY. (See Figure B)
The ball will fully charge in about
3-5 hours. Recharge the unit only
when it is completely discharged.
ATTACH ONE
ELECTROST A TIC PAD
Attach one disposable electrostatic
pad to the underside of the
Cleaning Frame and secure by
pushing the pad down onto the
black velcro tabs on the
Cleaning Frame. (See Figure C)
STEP BY STEP GUIDE:
2
step
1
step
FOR OPTIMAL CLEANING PERFORMANCE:
HELPFUL ROOM CLEANING TIPS:
PLACE THE CLEANING
FRAME IN THE CENTER
OF THE ROOM
Clear the room. Place the
Cleaning Frame in the center of the
room. (See Figure D) For prepa-
ration hints for clearing the room,
see page 6 of this operator’s man-
ual for our “For Optimal Cleaning
Performance” tips.”
Figure A
Figure B
Figure C
Figure D
RoboMop may come
upon a piece of furniture
like this couch, which
RoboMop can get
wedged up against and
get stuck. If RoboMop
can’t get out, just pull it
out and set it back to work
again. Or you can put a
small object in front of it,
so RoboMop can’t get
stuck underneath.
RoboMop can get
trapped between or
behind your furniture
because the entrance to
an area is barely big
enough for RoboMop
to fit through. Placing a
chair or plant in front of
the piece of furniture,
can solve the trouble so
it won’t stop working.
RoboMop may bump
into small items that can
spill and make a mess.
To make sure RoboMop
can clean the whole
floor; pick up any small
objects, just as you do
before you vacuum.
AVOID GETTING STUCK
AVOID MESSY SPILLS DON’T GET TRAPPED
3
step
For optimal cleaning performance, clear your floor of objects just as you would
before using a regular vacuum cleaner. Do not leave the following items on the
floor: clothing, loose papers, pull cords for blinds or curtains, power cords, or any
fragile items. RoboMop contacts walls, furniture and other objects as it cleans, so
please remove any items that may be pushed and knocked over by light contact
from RoboMop. If your room does not have a door, or there is access to a stairway
where RoboMop can fall down the stairs, simply block off the area with either a
chair, plant, gate or other object.
www.robomop.net
velcro tab
3
6
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomop robomop basic bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomop robomop basic in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 4,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info