English English 7 8
LOADING A DISC
1. Press the FUNCTION button on unit or remote control to select CD mode.
2. Press the OPEN/CLOSE button to open the CD door, “OP” will be shown on the
display.
3. Place an audio CD/MP3 DISC into the tray with the front side facing up.
4. Close the CD door. The display will show a flashing “- -”, then the total number
of tracks would be shown and the playback will start from track.
5. To remove the CD, press OPEN/CLOSE to open CD door, the display will show
“OP”. Hold the CD by its edges, and take it out carefully.
Note:
Make sure the disc is stopped before opening the CD DOOR.
To ensure good system performance; wait until the unit completely reads the
disc before proceeding.
If no disc loaded into the tray, or the disc is unreadable, the display will show NO
or Er.
PLAYING A DISC
1. The playback starts from track 1 automatically when reading the disc.
2. To pause playback, press PLAY/PAUSE BUTTON (15) on unit or (5) on remote.
3. To resume playback, press PLAY/PAUSE BUTTON (15) on unit or (5) on remo-
te again.
4. To stop playback, press STOP BUTTON (13) on unit or (16) on remote.
SELECTING A DESIRED TRACK/PASSAGE
To select a desired track
Press SKIP BACK/TUNING- BUTTON (12)/SKIP UP/TUNING+ BUTTON (14) on
unit or (4)/(14) on remote respectively in stop mode or during playing until the desi-
red track appears on the display. Press press PLAY/PAUSE BUTTON (15) on unit or
(5) on remote to start play.
To search for a particular passage during playback
Press and hold SKIP BACK/TUNING- BUTTON (12)/SKIP UP/TUNING+ BUTTON
(14) on unit or (4)/(14) on remote to scan the current playing track at high speed until
desired point (passage) appears, then release the button for normal playback mode.
Playback will start again from this point.
To select a song which track number exceeds 10
To select a song/track which number exceeds 10, Press M+ BUTTON (8)/M- BUT-
TON (7) on unit or 10+ BUTTON (6)/10- BUTTON (8) on remote control each time to
skip backward or forward 10 tracks, then press SKIP BACK/TUNING- BUTTON (12)/
SKIP UP/TUNING+ BUTTON (14) on unit or (4)/(14) on remote to select desired
track.
PROGRAMING TRACKS
Programming tracks of disc are possible when playback is stopped. Up to CD 20
tracks/MP3 99 tracks can be stored in the memory in any order.
1. In stop mode, press PROG BUTTON (10) on unit or MEMORY BUTTON (15) on
remote to enter program setting, the display will flash PROG and P01.
2. Press SKIP BACK/TUNING- BUTTON (12)/SKIP UP/TUNING+ BUTTON (14)
on unit or (4)/(14) on remote to select the first desired track to be programmed.
3. Press PROG BUTTON (10) on unit or MEMORY BUTTON (15) on remote to
enter. The display would flash PROG and P02.
4. Repeat steps 2 & 3 to store other desired tracks until all tracks programmed.
5. Press PLAY/PAUSE BUTTON (15) on unit or (5) on remote to start playback
from the first programmed track. The display will show 01 and the “PROG” indi-
cator will light up on LCD display.
6. Press STOP BUTTON (13) on unit or (16) on remote to stop program playback.
To clear the program, you may
Press STOP BUTTON (13) on unit or (16) on remote when the disc stopped.
Open the CD compartment lid, the program will be erased.
REPEAT
You can play one track or all tracks on the disc repeatedly.
To Repeat a Single Track
1. Press REPEAT / RANDOM BUTTON (11) on unit or (13) on remote during play,
the display will show a flashing “REPEAT“ and the current track will be played
over an over again till you press STOP BUTTON (13) on unit or (16) on remote.
2. To cancel repeat play, press REPEAT / RANDOM BUTTON (11) on unit or (13)
