8437
32
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
32
Remeha
Gas 3002 ECO
live and neutral inversion Switch off power and change connections.
switch off power, and change connections.
code not valid. The control unit does not recognize the boiler through the code connector.
check wiring. Check the wiring.
code not accepted. A wiring error has been made or a failure has occurred in the control unit.
please contact qualified personnel. Contact our service department.
flow sensor short circuit. Check the wiring of the respective temperature sensor.
return sensor short circuit. If wired correctly, replace the respective sensor and/or wiring.
heatexch. sensor short circuit.
flue sensor short circuit.
flow sensor open circuit.
return sensor open circuit.
heatexch. sensor open circuit.
flue gas sensor open circuit.
flow sensor overheat Too high temperature has been signalled.
return sensor overheat Check: - the water flow through the boiler/installation
heatexch. sensor overheat - the water level in the boiler
- the operating pressure (0.8 bar min.).
flue gas temperature too high Check: - the set maximum flue gas temperature (see par. 7.3.3, option no. 4)
Minimum setting: 15°C above maximum return water temperature
- the boiler setting
- the boiler for fouling
return temp. higher than heat exch. The return water temperature exceeds the first heat exchanger temperature.
temp. Check: - if the wiring of heat exchanger and return sensors have been inverted
- if the flow direction through the boiler is correct
return temp. higher than The return water temperature exceeds the flow water temperature.
flow temp. Check: - if the wiring of the flow and return sensors have been inverted
- if the flow direction through the boiler is correct
purge airpress. not reached During pre-ventilation the required min. air pressure differential across the boiler is not obtained.
Check: - the flue gas discharge, air supply, boiler and/or syphon for fouling
airpress. lost during purge - the diameter of the flue gas discharge/air supply pipes, using the tables of par. 5.6
- measurement tubes for fouling/humidity
insufficient airpress. during stage 1 The air pressure differential at low load is too low. It should be 50 Pa at least.
burning Check: - flue gas discharge, air supply, boiler and/or syphon for fouling
airpress. start not reached - fan, frequency regulator (see par. 10.9) and air pressure sensor
airpress. start lost - measurement tubes
insufficient airpress. during stage 2 The air pressure differential at high load is too low.
burning Check: - flue gas discharge, air supply, boiler and/or syphon for fouling
- fan, frequency regulator (see par. 10.9) and air pressure sensor
- measurement tubes
airpress. too high at stage 1 The air pressure differential is too high.
Check: - fan, frequency regulator (see par. 10.9) and air pressure sensor
airpress. detected when fan is off During standstill of the boiler too high a standstill draught is signalled (> 70 Pa).
Install a resistance in the flue gas discharge or air supply.
Check connections on air pressure differential switch (LDS).
Instructions
Failure message on LCD-display
32

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Remeha-Gas-3002-ECO

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Remeha Gas 3002 ECO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Remeha Gas 3002 ECO in de taal/talen: Engels als bijlage per email.

De handleiding is 1,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Remeha Gas 3002 ECO

Remeha Gas 3002 ECO Bijvullen ketel - Nederlands - 2 pagina's

Remeha Gas 3002 ECO Gebruiksaanwijzing - Deutsch - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info