500581
2
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
2
LAUNCHING A MANUAL BOOST
This function enables you to increase the tempera-
ture in your room rapidly and/or to dry your towels
for 2 hours. The device’s thermostat will not be in use
over this period.
The device will function normally again [the thermo-
stat will be used to regulate room temperature] as
soon as the timer stops.
Press the OK/Boost button: when it is released, the
light [5] will flash once to show that the manual
Boost has been registered, and the receiver light [1]
will flash red.
NOTE:
You can stop the Boost at any time by pressing the
button again. The receiver light [1] will stop flashing.
PROGRAMMING DAILY BOOSTS
The infrared room thermostat enables you to
programme 2 daily Boosts P1 and P2.
Programming a daily P1 Boost
Turn the cursor [8] to P1.
At the desired time, press the OK/Boost button for
three seconds to save the P1 cycle:
- The light [5] will flash twice briefly to indicate
that the daily Boost has been registered, and the
receiver light [1] will flash red.
- The Boost will start immediately for 2 hours and
will repeat after 23 hours and 15 minutes, and
then every 24 hours.
Example: The first morning at 7 o’clock, press the OK/
Boost button for three seconds. The next day, and on
subsequent days, the appliance will switch on at 6.15
for 2 hours. At the end of the Boost, the device goes
back to comfort mode.
Programming a second daily P2 Boost
Turn the cursor [8] to P1+P2.
Proceed as for programming P1 Boost .
- The second 2 hour Boost will start immediately
and will repeat after 13 hours and 15 minutes,
and then every 24 hours.
NOTE: You can stop the timer at an time by pressing
the OK/Boost button briefly.
Changing a programmed Boost
Turn the cursor [8] to the chosen programme and,
at the desired time, press the OK/Boost button
for 3 seconds: the new cycle will be saved and the
previous one will be erased.
NOTE: 2 quick flashes indicate that a P1 Boost [or
P2 Boost] programme has already been saved when
going into P1 mode [or P1+P2 mode].
RETURNING TO FACTORY SETTINGS
This will erase all programmes and restore the default
factory settings.
Turn the cursor [8] to
mode then press down for
at least 10 seconds:
- The light [5] will flash twice to indicate that the
re-set has been registered.
- P1 and P2 programmes will be erased.
CALIBRATING THE THERMOSTAT
It is normal for there to
be a 1 to 2°C difference
between the temperature
displayed on the emitter
and that measured by a
thermometer.
If you wish to synchronize
these two values, let your
thermostat regulate the
temperature for at least
an hour and then proceed
as follows:
Example: you have set
your thermostat to
21°C. After an hour of
regulating the tempera-
ture, the thermometer is
displaying 23°C.
Remove the temperature knob, taking care not to
turn it at the same time.
Remove the knob’s central notched axle [with a
small pair of pincers] and put the axle back in the
thermostat pivot, without making it move round.
Then place the knob back so as the temperature
you have measured is the same as that shown on
the thermostat dial.
SETTING A MAXIMUM TEMPERATURE
FOR THE THERMOSTAT
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Radson Minuterie bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Radson Minuterie in de taal/talen: Nederlands, Engels, Frans als bijlage per email.

De handleiding is 0,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info