587737
21
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
21
Wiring Diagram
Connecting the outdoor part
The connections of the outdoor part are located inside
the unit above the connection valves. Proceed as fol-
lows to connect the lines:
1. Remove the cover of the terminal strip on the right-
hand side of outdoor part.
2. Guide the lines through the strain relief.
3. Connect the customer-supplied connection lines of
the units to the outdoor part and the indoor unit as
shown in the figure below.
4. Also connect the sensor line of the RKS 350 H unit
to the corresponding connections on the outdoor part
and indoor unit.
5. Secure the control lines in the strain relief and re-
place the cover of the terminal strip.
Condensation
Condensation flow to the outdoor part
Condensation forms during heating operation on the
plate fin exchanger of the outdoor part because tem-
peratures below the dew point are reached.
The lower housing panel of the outdoor part is designed
to function as a drain tray. A condensation connection
has been supplied beneath the condenser or in the cen-
tre of the tray to be used by means of the seal.
If the unit is used for heating in areas susceptible to
frost, the lower housing panel must be kept free of frost
to ensure that the condensation can always drain out.
Condensation drainage on the indoor unit
Condensation forms during cooling operation on the
plate fin exchanger of the outdoor part because tem-
peratures below the dew point are reached.
The drainage trays of the indoor units are equipped with
a condensation hose. This hose must be placed at an
incline to ensure that the condensation drains.
Condensation hose on the outdoor part
Condensation can be guided over longer distances us-
ing a customer-supplied condensation hose.
Ensure the following before laying the condensation
hose:
àMake sure that there is an adequate incline for drain-
age.
Minimum of 2 %.
àWhen the unit is in operation at an outside tempera-
ture of below 0 °C, the hose must be protected
against frost.
If necessary, use a hose heating mechanism.
àAlways use suitable hose clips.
àAfter the hoses have been put into place, you must
check that the condensation flows freely.
1. Place the seal on the hose
connection piece.
2. Press the connection piece
into the opening for this pur-
pose.
Seal
Connection
piece
Resulting
connection
Assembling the condensation connection
RKS 327 H and RKS 335 H
Outdoor part
Compressor control
Neutral conductor
To the reverse valve
Protective conductor
1
N(2)
3
To the condenser fan
PE
4
N
L
PE
N
L
PE
Power suppl
y
Indoor unit
1
N(2)
3
230 V~,
50 Hz,
L1/N/PE
PE
4
RKS 350 H
Outdoor part
Compressor control
Neutral conductor
To the reverse valve
Protective conductor
1
N(2)
3
To the condenser fan
PE
4
N
L
PE
N
L
PE
Power suppl
y
Indoor unit
1
N(2)
3
230 V~,
50 Hz,
L1/N/PE
PE
4
Sensor line to the AT
Sensor line to the AT
Plug
Plug
RKS 371 H
N
L
PE
N
L
PE
Power suppl
y
Indoor unit
230 V~,
50 Hz,
L1/N/PE
Outdoor conductor
Neutral conductor
To the reverse valve
To the condenser fan
Protective conductor
To the compressor
Sensor line
Sensor line
Not in use
N(2)
3
4
PE
5
1
7
8
N(2)
Outdoor part
3
4
PE
5
1
7
8
6
contactor
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO RKS335H bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO RKS335H in de taal/talen: Engels als bijlage per email.

De handleiding is 1,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO RKS335H

REMKO RKS335H Gebruiksaanwijzing - Nederlands - 28 pagina's

REMKO RKS335H Gebruiksaanwijzing - Deutsch - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info