587592
9
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
9
Manual operation
The unit can be manually operated if, for example, the
infrared remote control is not functioning properly or
has been lost.
Open the air inlet grille of the indoor unit and press the
button on the right side.
The following operating modes are then activated:
MODE = Automatic
(Operating cycle of the compressor
On 20 min. Off 10 min.)
TEMP. = 24°C, FAN = Automatic
SWING = On, TIMER = Off.
Shutting Down the Unit
Temporary shutdown
1. Let the unit run in cool mode for 30 minutes at a
temperature setting of 31°C.
2. Switch the indoor unit off using the remote control.
3. Disconnect the system with the main switch or fuse
protection from the power supply.
4. Check the indoor unit for visible damage.
5. Clean the indoor unit as described in the
“Maintenance and Service” section.
6. If possible, cover the outdoor unit with a plastic
sheet to protect it from weather conditions.
Permanent shutdown
For environmental safety reasons, the air conditioners
may only be disassembled by authorised service cen-
tres.
Manual air distribution
There are individually adjustable air directing plate fins
on the air outlet side for horizontally distributing the air.
Set the air directing plate fins in the desired position
with the left and right adjustment levers.
*
Never adjust the fins when the unit is in automatic
swing mode! Do not reach into the unit!
There is a risk of injuring your hand on the fan
motor.
LED display on the indoor unit
POWER On / Off (red)
PROTECT Compressor protection (green)
RUN Compressor mode (green)
TIMER Timer mode (yellow)
Display Room temperature / target temperature
error code
The display changes to the target temperature display
when the settings are made with the remote control.
Left adjustment
lever
Right adjustment
lever
Cause
E3
RUN and TIMER LEDs blink alternately.
Unit switches off after approx. 30 seconds.
Fan motor
E5 TIMER LED blinks. Room air sensor
E6 RUN LED blinks. Frost protection
sensor
E9 The LEDs blink alternately for 20 minutes.
Unit switches off after another 20 minutes.
Insufficient refriger-
ant
LED error code
First, remedy the cause of the problem and then reset
the error code display by switching the unit off and off.
Malfunction display
1 Indoor unit ML ...-IT
2 Outdoor unit ML ...-AT
3 Infrared remote control
4 Refrigerant pipes
5 Air inlet grille
6 Air outlet fin with swing motor
7 Manual air directing plate fin
(covered)
System Structure
11
3
4
7
8 9
Outside
Inside
2
1
14
12
10
13
6
15
5
8 Display
9 Receiver
10 Manual mode switch
11 Condenser fan
12 Wall lead-through
13 Shut-off valve
14 Condensation connection ML ...-IT
15 Air outlet
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO ML260 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO ML260 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO ML260

REMKO ML260 Gebruiksaanwijzing - Nederlands - 24 pagina's

REMKO ML260 Gebruiksaanwijzing - Deutsch - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info