721960
24
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
24
CARE AND MAINTENANCE
13. Connect the battery harness to the new front battery
according to the battery wiring diagram. See figure 21.
14. Connect the battery harness to the new rear battery
according to the battery wiring diagram. See figure 21.
Make sure you tighten the fasteners so that the
connections are secure.
15. Install the new rear battery by lowering it into the power
base. Ensure the actuator is straight up and down next
to the rear battery. Connect the quick release battery
connectors to the new rear battery.
16. Install the new front battery by sliding it into the front
of the power base. Connect the quick release battery
connectors to the new front battery.
17. Reinstall the top cover by sliding the rear of the top cover
under the lip of the rear door and then sliding into place.
18. Reinstall the front cover.
19. Return the seat to an upright position.
20. Reinstall the detent pin into the top of the actuator and
ensure that it is secure. See figure 4.
21. Reinstall six (6) Phillips flat head screws if seat pan was
removed.
22. Tighten the rear pivot hardware.
23. Charge the batteries. See “Batteries and Charging.
Battery Replacement
A battery wiring diagram is printed on a decal located on
the front cover. See the specification table for correct battery
specifications.
Battery posts, terminals, and related accessories
contain lead and lead compounds. Wear goggles and
gloves when handling batteries and wash hands after
handling.
The batteries in your power chair should only be
serviced or replaced by a Quantum Rehab Provider or a
qualified technician.
Do not replace batteries when seat is occupied.
Power chair batteries are heavy. See specifications
table. If you are unable to lift that much weight, be sure
to get help. Use proper lifting techniques and avoid
lifting beyond your capacity.
Do not mix old and new batteries. Always replace both
batteries at the same time.
Keep tools and other metal objects away from the battery
terminals. Contact with tools can cause electrical shock.
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See
“Your Power Chair.
3. Loosen the rear pivot hardware until the Nylock nut is a
few threads from being removed.
4. Remove the detent pin from the top of the actuator. See
figure 4. If there is any difficulty in reaching the pin from
under the seat, the seat pan may be removed. Remove
six (6) Phillips flat head screws to remove the seat pan.
5. Pivot the seat toward the rear of the power chair and
support the seat in this position. Take care to ensure that
the recline actuator does not damage the rear door of
the power chair while the seat is pivoted rearward.
6. Remove the front cover by squeezing the release
handles (see figure 21) and lifting the front cover up
and away from the power base.
7. Remove the top cover by lifting it straight up and off of
the power chair.
8. Disconnect the actuator harness.
9. Disconnect the quick release battery connectors. See
figure 1.
10. Remove the front battery from the power base by sliding
it forward and out of the power base.
11. Remove the rear battery by lifting it up and out of the
power base.
12. Disconnect the battery harness from each battery.
PROHIBITED!
WARNING!
WARNING!
MANDATORY!
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Quantum Q4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Quantum Q4 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Quantum Q4

Quantum Q4 Gebruiksaanwijzing - Nederlands - 36 pagina's

Quantum Q4 Gebruiksaanwijzing - Deutsch - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info