778522
13
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
24 25
0.43-0.51mm
Cleaning or replacing the air filter
WARNING!
Never run the engine without the air lter element installed:
1. Loosen the fastener (A) that holds the cover (B).
2. Open the cover and remove the lter (C).
3. To loosen debris, gently tap the lter on a hard surface. If the lter is excessively dirty,
replace with a new lter.
4. Install the air lter.
5. Install the cover tabs (D) into the slots (E).
6. Close the cover and secure with the fastener (A).
Cleaning or replacing the spark plug
1. Once the engine has cooled, pull off the spark plug boot with a twist. Remove the
spark plug using the socket spanner supplied.
2. Clean the plug with a wire brush.
3. Using a feeler gauge, set the gap to 0.51mm.
4. Install the spark plug carefully by hand to avoid cross-threading.
5. After the spark plug is seated, tighten with the spanner to compress the washer.
Adding the oil
Rell with SAE 30 oil or equivalent, i.e. SAE 5W/30, SAE 10W/30). When the dipstick is
rested on the ller pipe, the oil level must be between the min. and max. marks on the
dipstick.
See ‘Filling with engine oil’. Do not overll.
Start the engine and allow it to run briey.
Stop the engine, wait one minute and check the oil level. Top up if necessary.
Replacing the cutting blade
WARNING! USE GLOVES.
Before you remove the grass collection bag, stop the engine and wait until the
blade stops completely.
You will need garden gloves (not provided) and a spanner wrench to remove the
blade.
Always handle the blade with care; sharp edges could cause injury.
NEVER hold the blade directly by hand.
Renew your metal blade after 36 hours of mowing or after 2 years, whichever is sooner,
regardless of condition.
Regularly check your blade. If the cut of your grass is poor, the blade might be blunt.
Damaged blades not only result in a bad cut, they cause excessive vibration and
uneconomical running of the engine. If the blade has worn excessively and become pitted
and blunt, it should be replaced or sharpened.
Note: The blade carrier is designed to break under heavy blade impact to protect the
machine. If this happens, also replace the blade carrier. This can be purchased from
www.gardenservicecentre.co.uk.
To replace the blade, hold the blade and unscrew the blade bolt counterclockwise using a
spanner wrench. Remove the washer and the blade.
Inspect the blade adaptor for any signs of damage.
Fit a new blade, locate the blade on the two studs on the blade ange and then replace the
washer and bolts.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Qualcast QSPP53 - 484348 - XSZ53D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Qualcast QSPP53 - 484348 - XSZ53D in de taal/talen: Engels als bijlage per email.

De handleiding is 10.71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info