698698
5
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
8
EN
9
INSTALLING
1. Select the correct voltage required on the back of the unit amplifier that matches the voltage coming
from the mains supply. Use the power cable supplied in the package to connect the equipment up to the
mains supply.
2. Check that the unit is switched off.
3. Connect up the auxiliary units that you want to use to the equipment‘s inputs. (RCA 1-3, TosLink, SPDIF,
USB) right channel = red / left channel = white or the symmetric analog XLR inputs can be used with any
compatible signal source.
(XLR pin assignments: Pin 1= ground; Pin 2 = plus / signal; Pin 3 = minus)
4. The screw terminals at the back are used for the speaker connections.
5. (See back of the equipment: right channel = 1 / left channel = 7). You must also ensure that the plus
and minus connections on the amplifier concur with the plus and minus connections on the speakers in
order to prevent polarity reversal.
6. Now switch your amplifier own.
Switch the mains switch (9) into the ON position on the back. The standby LED on the front will come
on.
7. Now press the multifunction knob (2) on the front or the button (2) on the remote control to start your
equipment.
Note:
As your A8 uses a special power-saving standby circuit, you can always switch on / off during normal oper-
ation using the multifunction knob on the unit or the RC-2 remote control.
The RC-2 remote control makes it easier for you to change your settings.
Mute (button 3)
Balance setting (buttons 6 & 7)
Multilevel display brilliance setting (button 15)
Input level setting for all inputs (button 14)
Example: Input level setting
Use buttons 8 (-) or 9 (+) to select the signal source and then press button 14 (Prog.) and use the volume
buttons (4 & 5) to set up the input volume to suit yourself. Press button 14 (Prog.) once again to save the
settings.
AMBIENT CONDITIONS
Notes about the removal and the correct environmentally-friendly disposal of old batteries.
The symbol shown here can be found on the equipment‘s enclosure, the packaging as well as in the doc-
uments or the operating manual. It tells you that batteries provided with the equipment as well as those
supplied with or fitted in other units must never be disposed of in household waste. They must be disposed
of in an environmentally-friendly way (in compliance with the local regulations or European Directives
2002/96/EU and 2006/66/EU).
You should find out where the nearest collection point for electronic scrap is or where the recycling site is.
Correct disposal of the equipment and the batteries will help to preserve our resources and prevent physi-
cal and environmental damage. The battery (CR2032) supplied with the remote control contains lithium and
it must be disposed of in an environmentally-friendly way as described above.
Proceed as described in the following section to replace or remove the battery fitted in the remote control.
1. Undo the screw in the cover underneath the remote control and then remove the cover.
2. Remove the battery by sliding it out of its holder.
3. You must ensure that the new battery‘s polarity is correct when you fit the new one! The side of the
battery marked with (+) must point upwards so that it makes contact with the part of the holder marked
with (+).
4. Refit the cover and use the screw to secure it in place.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Quadral AURUM A8 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Quadral AURUM A8 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info