572623
4
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
4
5
Make sure that the batteries have been installed according to the instructions
found in the battery installation section of this manual.
USE AND TESTING
Enter a dark area before turning on the binocular.
Remove the objective caps.
Activate the device by pushing the “ON” (2) button. The green LED indicator (3)
lights up. If the batteries are low, the colour of the indicator will turn red.
You can test your binocular in a light area without removing the protective caps.
This will not damage your unit.
If the subject to be viewed is in a completely dark area, including lowlight
shadow areas; activate the infrared illuminator (4) by pushing the “IR” button
(5). To adjust the IR power, rotate the controller (6).
Direct the turned on binocular at an object at a distance of about 10-100
meters. Rotating the eyepieces (7), focus on the tube's screen - rough surface
or tiny dark dots are visible. Rotate the objective lenses (1) until the image
quality is optimal. Re-focus the eyepieces, if necessary. After this adjustment
you may not rotate the eyepieces irrespective of the distance and objective
lenses.
Point the binocular at an object to be viewed and adjust the final focus by
rotating the objective lens focusing ring until the image is optimal. When
screwing the objective lenses into the housing, it focuses on farther objects,
when screwing out - on closer ones.
When you are finished using your binocular place the caps back onto the
objective lenses and turn off the unit by pushing the “ON” (2) button, the LED
indicator will go out. Put the binocular into the carrying case.
CAUTION!
Your device can be used in extreme cold. However, when the unit is brought
back into a warm environment, you must wait approximately 2-3 hours before
using the unit again. Failure to do so may result in damage as a result of
condensation accumulating on the internal circuitry of the unit.
TROUBLESHOOTING
The scope will not turn on.
Check that the batteries are installed properly. Install the batteries according to
the (+) and (-) polarity, ensuring that the markings on the battery and battery
compartment correspond with one another. Check the battery contacts to
ensure they are clean and free of corrosion; if necessary, clean the contacts
with rubbing alcohol. Also check that the cap of the battery department is fully
closed, otherwise the device will not operate. If necessary, replace the
batteries as they may be depleted. Also be sure that the “ON” button has been
pushed and the green LED is on.
Distinct black dots appear on the screen.
These dots are cosmetic blemishes resulting from tube production processes
and do not interfere with the reliability or performance of the scope and are not
a defect.
The image “snows”.
Image may “snow” in a dark environment during 30-60 seconds after the
device is activated; this effect disappears soon. Image may slightly “snow” if
the device was previously operated without the lens caps at a high level of
luminance. Image may also “snow” if the device is operated in complete
darkness with the IR illuminator off.
The image is not focused.
Adjust the focus of the eyepieces and the objectives (see “Use and Testing”
section). Check that the lenses are not foggy or dusty; if they are, carefully
clean the external surfaces of lenses with a soft cotton fabric. Replace the
batteries if the total battery charge is less than 2.2V.
When the unit is brought into a warm environment from a cold one,
condensation may appear on the internal lenses; you must wait two hours
before using the unit.
Visibility decreases or disappears.
Turn the power off and turn the binocular away from the light source; visibility
will restore itself immediately.
During long-time storage please remove the batteries to prevent possible
leakage. The battery cover must be fully screwed during long-time storage.
STORAGE
Clean the lens with professional lens cleaning supplies intended for use with
multicoated optics.
Blow any dust or dirt off the lenses using dry, compressed air.
Clean the unit housing with a soft, clean cloth.
MAINTENANCE
Match the boss of the battery compartment with the groove of the battery cover.
The cover should tightly fit the body along the perimeter, avoid skewing. Lock the
cover by turning the screw of the battery cover 90° counterclockwise.
OPEN
5 6
7
2 3
++
+
-
-
90º
4 1
1
7
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pulsar Edge GS2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pulsar Edge GS2 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info