572627
5
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
6
7
DESCRIPTION
The Digisight LRF N850/N870 riescope is designed for observation and
shooting in twilight or nighttime. In complete darkness (no stars or the Moon) use
of the built-in IR (or laser) Illuminator with 780nm wavelength (visible range) or
915nm wavelength (invisible range) is highly recommended. The riflescope is
equipped with a built-in multifunctional rangefinder with a working measuring
range of 400 metres. Your riflescope is a versatile device designed for a wide
range of professional and amateur applications such as hunting, sports
shooting, night video recording and observation.
GUIDELINES FOR OPERATION
The riescope has been designed for long-term use. To ensure long
performance, please adhere to the following:
Before use make sure that you have installed and fixed the mount according
to the instructions of the section “Installation of mount” (section 9 “Operation”).
Store with the lens cap on in the carrying case.
Switch off the scope after use.
The riflescope cannot be submerged in water.
Attempts to disassemble or repair the scope will void the warranty!
Clean the scope's optical surfaces only if necessary, and use caution. First,
remove (by blowing with a blower brush or canned air) any dust or sand particles.
Then proceed to clean by using camera/lens cleaning equipment approved for
use with multicoated lenses. Do not pour the solution directly onto the lens!
The riflescope can be used in various operating temperatures. However, if it
has been brought indoors from cold temperatures, do not turn it on for 3 to 4
hours. This will prevent external optical surfaces from fogging.
If the scope is unable to mount onto the rie securely, or you have doubts
about the mounting system, see a qualified gunsmith. Using the weapon with a
poorly mounted scope can lead to inaccurate target shooting!
To ensure reliable performance, it is recommended to carry out regular
technical inspections of the unit.
Do not leave batteries in the unit if it is not going to be used for an extended
period.
Batteries shall not be exposed to excessive heat such as sunshine, re or the like.
INSTALLATION OF BATTERIES
Unscrew and remove the battery cover from the battery compartment (15).
Install four AA batteries according to the marking on the battery compartment cap.
Replace and screw back the battery cover tightly.
Battery charge level is displayed on the status bar ( ).
In case of complete battery discharge, a red icon is flashing on the status
bar and in the centre of the display.
Note: to ensure long and reliable operation it is recommended that you use
quality rechargeable batteries with a capacity of at least 2500 mAh. Please do
not use batteries of different types or batteries with various charge levels.
EXTERNAL POWER SUPPLY
The riflescope can be powered with an external DC power supply (2.1mm pin)
with stabilized voltage ranging from V to 15V (max. consumption power 3W) or 9
a 12V vehicle socket.
External power supply (AC/DC) is to be connected to “Power (10) jack
located on the right side of the riflescope.
Note: central pin of the power supply that you connect to the power” jack of the
riflescope, must have marking “+”. The power supply may have marking .
Connection of an external power supply (icon on the status bar)
automatically cuts off power supply from batteries.
External power supply DOES NOT charge the batteries in the riflescope!
Attention! We suggest that you use battery packs EPS3 or EPS5 ensuring from
9 to 20 hours of continuous operation.
OPERATION
Installation of mount
Before using the riflescope you need to install the mount.
The riflescope can be used with various mount types such as Weaver, Euro-
prism, Los, MAK adapter etc. that allow the scope to be installed on different
types of rifles.
The mounting holes in the base of the riescope enable the mount to be
installed in one of the multiple positions. The choice of the mounting position
helps the user to ensure the correct eye relief depending on the rifle type.
Attach the mount to the base of the riescope using a hex-nut wrench and
screws (see installation scheme on page 5).
.Install the scope on the rifle and check if the position is suitable for you
If you are happy with its position, remove the scope, unscrew the screws
halfway, apply some thread sealant onto the thread of the screws and tighten
them fully (do not overtighten). Let the sealant dry for a while.
The riflescope is ready to be installed on a rifle and to be zeroed.
After first installation of your riflescope on a rifle, please follow instructions in
the section “Zeroing”.
Note: Please check that your riflescope is duly zeroed after changing a mount.
Starting the scope and image setup
Install the batteries according to the instructions in Section 7 “Installation of
batteries” or connect an external power supply.
Open the lens cap (2).
Turn on the riflescope turning the selector switch (3) to the “ON” position
within a couple of seconds the display will light up.
Adjust the sharpness of onscreen symbols with the eyepiece adjustment
ring (4). After this adjustment no further dioptre adjustment should be required,
regardless of distance or other factors.
To adjust the display brightness, rotate the controller (7). Brightness level
from 0 to 20 is shown next to the icon in the upper part of the display and then
on the status bar.
Press the controller (7) to switch to display contrast setup mode. Contrast
level from 0 to 20 is shown next to the icon in the upper part of the display and
then on the status bar.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pulsar Digisight LRF N870 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pulsar Digisight LRF N870 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 5,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info