572609
6
Verklein
Vergroot
Pagina terug
1/55
Pagina verder
8
9
9
EXTERNAL POWER SUPPLY
The sight can be powered with an external DC power supply (2.1mm pin)
with stabilized voltage ranging from 8V to 15V or a 12V vehicle socket.
џ Connect the plug (13) of the cable to the jack (10) of the sight by matching
the notch in the plug connector and the protrusion of the jack (10) (see the
scheme).
џ Secure the cable by turning clockwise the locking ring of the plug (13).
џ Connect the external power supply (AC/DC) or car adapter to the jack (15)
of the cable.
Note: central pin of the power supply that you connect to the “power” jack of
the sight, must have marking “+”.
џ The power supply may have marking .
џ Connection of an external power supply (icon on the status bar)
automatically cuts off power supply from batteries.
џ External power supply DOES NOT charge the batteries in the sight!
Attention! We suggest that you use battery packs EPS3 or EPS5 ensuring
from 9 to 20 hours of continuous operation.
OPERATION
Installation of mount
Before using the sight you need to install the mount (12).
The sight can be used with various mount types such as Weaver, Euro-
prism, Los, Side mount, MAK adapter etc. that allow the scope to be installed
on different types of rifles.
The mounting holes in the base of the sight enable the mount to be installed
in one of the multiple positions. The choice of the mounting position helps the
user to ensure the correct eye relief depending on the rifle type.
џ Attach the mount to the base of the sight using a hex-nut wrench and
screws (see installation scheme).
џ Install the scope on the rifle and check if the position is suitable for you.
џ If you are happy with its position, remove the scope, unscrew the screws
halfway, apply some thread sealant onto the thread of the screws and
tighten them fully (do not overtighten). Let the sealant dry for a while.
џ The sight is ready to be installed on a rifle and to be zeroed.
џ After first installation of your sight on a rifle, please follow instructions in the
section “Zeroing”.
Note. Please check that your sight is duly zeroed after changing a mount.
Powering on and calibration
џ Press briefly the “ON” (1) button to power on the sight. In case of low
battery icon will start flashing.
џ Do the calibration of image. Calibration levels background temperature of
the microbolometer and eliminates image flaws.
џ There are three calibration modes: manual (M), semiautomatic (H) and
automatic (А).
8
Manual (silent) calibration mode
џ The lens cap (8) should be closed.
џ Power on the sight with the “ON” (1) button, hold down the controller (9) for
two seconds to enter the menu.
џ Rotate the controller to select option Cal. Press the controller.
џ Rotate the controller to select mode М. Press the controller to confirm. To
exit the menu, press and hold the controller (9) for two seconds or wait 10
seconds for automatic exit.
џ Press the CAL (2) button to calibrate. The image will freeze for 1-2
seconds. Then open the lens cap. Calibration is completed.
џ In case you see image flaws (such as frozen image, vertical stripes etc.) re-
calibrate the unit with the lens cap closed.
Semiautomatic calibration mode
џ Power on the unit, open the lens cap.
џ Hold down the controller (9) for two seconds to enter the menu.
џ Rotate the controller to select option Cal. Press the controller.
џ Rotate the controller to select mode H. Press the controller to confirm.
џ Press the CAL (2) button to calibrate. The image will freeze for 1-2 seconds
and you will hear the sound of the internal shutter. Calibration is
completed.
Automatic calibration mode
With the automatic calibration mode the thermal imager calibrates by itself
according to the software algorythm. The detector (microbolometer) is
closed with the shutter automatically. User assisted calibration with the CAL
(2) button is allowed in this mode.
џ Power on the unit, open the lens cap.
џ Hold down the controller (9) for two seconds to enter the menu.
џ Rotate the controller to select option Cal. Press the controller.
џ Rotate the controller to select mode A. Press the controller to confirm.
џ At the moment of the automatic calibration the image will freeze for 1-2
seconds and you will hear the sound of the internal shutter.
џ Time intervals between calibrations depend on the heat of the detector.
The unit may require calibration more frequently on activation.
Focusing and image adjustment
џ Open the lens cap (8).
џ Adjust sharp image of the display icons by turning the eyepiece ring (5).
џ To adjust display brightness, rotate the controller (9). Brightness level
(from 0 to 20) will appear next to the brightness icon in the top right
corner of the display.
џ To adjust display contrast, press the controller (icon appears) and rotate
it. Contrast level (from 0 to 20) will appear next to the contrast icon in the
top right corner of the display.
џ Point the unit at a warm object located at a certain distance, 100 meters, for
example.
џ Adjust the focus by turning the ring for lens internal focusing (6).
џ After this adjustment no further dioptre adjustment should be required,
regardless of distance or other factors. Adjust image quality only with the
ring (6) for lens internal focusing.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pulsar Apex LD50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pulsar Apex LD50 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info