566857
1
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
HALOGEN HAND LAMP 500W + camera
EN - 1
PLI-126
We thank you for the purchase of this Profile product.
Note: It is important that you read this manual carefully
before using the product Then keep this manual in a safe
place.
Note
Check if building regulations apply to your area whereby
you must have the halogen hand lamp installed by an
accredited electrician. An electrician can give you
information about correct wiring. Never install the fitting
outside in rainy weather.
SWITCH OFF THE POWER BEFORE YOU INSTALL
THE HALOGEN HAND LAMP.
Technical information
Working voltage: 220V. (50Hz or 60Hz)
Maximum lamp power: 500W.
Maximum current strength: 10/16A.
Dustproof and splash proof: IP44.
Dimensions: B185 x H265 x D130 mm.
160MB built-in memory
Picture format: JPG
Maximum resolution: 2.0M pixels
Automatic camera focus.
Passive infrared sensor (PIR).
Sensor angle: 52°.
Sensor range: 9 metres at 25°C.
Lighting time: +/- 10 sec. – 10 min.
Correct installation
With installation outside preferably choose a place
under a roof.
Do not place the sensor head in direct or reflected
sunlight. The halogen hand lamp may then switch on
when not required and photos may be overexposed.
The sensor works best with movement “crosswise”
through the sensor's detection field.
Connect the halogen hand lamp to a circuit with wall
switch: the current must be able to be interrupted to fit
the SD card.
Unscrew the stainless steel bolts on the side to take
the holder from the fitting.
Fix the holder to the wall with 2 screws. Do not fix the
holder to a highly flammable surface. Leave a distance
of at least 1 m between the halogen hand lamp and the
object to be illuminated. Install the halogen hand lamp
at least 2.5 m above the ground.
Fix the halogen hand lamp back on the assembled
holder.
Unscrew the cover of the cable connection.
Pull the power supply wires through the opening with
the rubber packing.
Connect the electric wiring according to figure 1.
The halogen hand lamp must be connected to mains
voltage of 230V, max. fusing 16A.
Fig. 1
Screw the cable connection cover tight again.
Other uses than described above can cause damage
to the product and increase the risk of short-circuit,
fire, electric shocks, etc.
The product may not be adapted as a whole. The
safety instructions must be strictly observed.
Summary of the functions
lighting time setting
light intensity setting
USB port
SD port
Digital display
MODE button
SET button
1) Setting the lighting time (TIME):
With this adjusting knob you can set the period of the
light staying on after switching on. You can set the
time from 10 sec. to 10 min.
2) Setting the light intensity (LUX):
With the second button you set the working of the
sensor to match the intensity of the ambient light.
If the arrow is pointing to the sun the sensor responds
in both daylight and at night. If the arrow is pointing to
the moon the sensor will only respond at night. In
between the sensor responds in half-light.
3) USB port: to connect the lamp to a PC. For this use
the USB cable supplied, length = 2m.
4) SD port: Here you can fit an SD card for saving
photos. Always push the SD card fully to the end to
make sure the photos are saved.
*
L = phase
*
= earthing
* N = neutral
wire
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Profile PLI-126 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Profile PLI-126 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Profile PLI-126

Profile PLI-126 Gebruiksaanwijzing - Nederlands - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info