566798
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
3-in-1 DIGITAL DETECTOR EN - 1
PIN-136
We thank you for the purchase of this Profile product.
Please note: It is important that you read this manual
before using the product And be sure to save this
manual for possible use later.
Features and advantages
1. foot for vertical fixing
2. Spirit level
3. Feet for horizontal fixing
4. foot for spirit level
5. Function key metal
6. Function key laser
7. Function key wood
8. on-key
9. LCD display
10. Adjusting ring laser angle
Features and advantages
Detection of wood/metal and live 230V wires –
detects to a depth of maximum 3/4" (19 mm)
Signals obstacles with a noise and displays this on the
LCD display. 180” adjustable laser with spirit level
and perpendicular line glass
LCD display with graphic display
LED light for continuous detection of live wires
Laser line projection 6.5 metres
With adjustable legs for bringing the laser level
Vertical and horizontal fixing feet
Simple key operation
Ergonomic designed to enhance comfort and grip
Automatic switching off
Low battery capacity indication
Safety instructions
If the warnings are not heeded this can result in
physical injury.
Heed the following warnings to prevent physical
injury:
Never remove the warning labels.
• Do not point the laser beam directly at other people's
eyes.
• NEVER look directly into the laser beam.
• Do NOT point the laser beam at a reflective surface.
• Do NOT use near children and do not allow use by
children.
• Never disassemble the laser.
Always switch the laser off when the appliance is not
in use.
Introduction
The unit uses electronic signals to locate the position of
wooden beams, connections or live AC wires under
plasterwork and
other common wall materials. When the edge of the
beam/plank is detected the unit's LCD display gives a
visual and acoustic signal to enable you to
exactly determine the edge of the beam. You can mark
the place of the beam edges with a pencil line. The unit
generates a vertical laser plane and turns 45 or 90
degrees to the right or to the left to generate a straight
laser line.
Operating instructions
Detection mode is selected with the function keys - metal
or wood.
The standard mode is the detection of wooden beams.
The preferred mode must be selected before "on" is
pressed.
Calibration
Calibrate the unit on a wall before you scan for wooden
or metal elements or power lines.
Please note! The calibration of the unit must take place
on a wall in which you know there are no wooden/metal
or electrical parts. Still wet or just painted surfaces can
also affect the good calibration of the unit. If you
do not adhere to the points mentioned above, the unit
will not give the correct location of concealed objects in
walls and ceilings.
Different surfaces
Wallpaper: there is no difference in the operation of the
sensor with surfaces hung with wallpaper or textiles
unless this wallpaper contains metallic foil or fibres.
Plasterwork or lath walls: the unit will function
correctly unless the plasterwork or laths are
exceptionally thick or contain metal meshing.
Ceilings or surfaces with a textured finish: when a
rough surface has to be scanned, such as a sprayed
textured ceiling, you can use a piece of cardboard to
scan the surface. Carry out the abovementioned
calibration WITH the piece of cardboard between the
sensor and the surface.
Detection of wooden beams
When the unit is switched on, as default it is in the
detection mode for wooden beams.
1. Slide the unit in a straight line over the surface. As
the unit comes closer to the beam, more lines will
be seen as shown in picture 2. When the edge of
the beam is detected, the wood indication and the
edge line will be seen as in figure 3. The unit
sounds a repeated beeping.
2. Use the indication line to mark the edge of the
beam.
3. Slide further over the beam. When the indication
goes out and the unit stops beeping the other edge
has been detected.
4. Carry out an extra check of the location of the beam
by approaching it from the other side.
5. The middle point between the markings indicates
the middle of the beam.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Profile PIN-136 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Profile PIN-136 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Profile PIN-136

Profile PIN-136 Gebruiksaanwijzing - Nederlands - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info