604342
31
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
S3.45 Assembly and Maintenance Guide
page 31
18. Feed Chest Press Cable
A. Insert the Selector Stem into the Chest Press
Weight Stack with the threaded hole at the top. Hold
the Selector Stem with several holes above the Cap
Plate. Insert the Weight Pin to suspend the Selector
Stem. Place the loop end of the Weight Pin Lanyard
into the U end of Cable 43623-103. Align the U end
of the Cable, the top of the Selector Stem, and the
Cap Plate. Attach using
one 1½-inch socket cap bolt
Wrench tighten. Remove the Weight Pin and lower
the Cap Plate.
B. While standing on a step ladder, loop the middle
section of the Cable through the window in the Top
Frame and over one 6-inch pulley. Lower the pulley
and Cable into the window and attach using
one 2¾-inch bolt
two ½-inch step spacers
one locknut
Finger tighten.
Note: If you have the Leg Press option, see the
Leg Press assembly instructions for an alternate
Cable and pulley installation step.
C. Place the Cable between the cable retainer and
one 4½-inch pulley. Attach to the Pulley Plate using
one 2½-inch bolt
two washers
one ½-inch barrel spacer
one locknut
Wrench tighten.
D. Remove the Spring Clip from the other end of the
Cable. Feed the Cable through the window in the
Rear Upright and attach one 4½-inch pulley using
one 2¾-inch bolt
two ½-inch step spacers
one locknut
Step 18. Feed Chest Press Cable
Ensure the Cable passes between the pulley and
retainer pin. Wrench tighten.
E. Place the Cable over one 4½-inch pulley and
attach to the upper hole in the Press Arm Flats
using
one 2-inch bolt
two washers
one locknut
Finger tighten.
F. Ensure the Cable wraps around the pulley and
then feed the Cable back through the Press
Arm Flats. Wrap the Cable over and around one
4½-inch pulley and attach it to the Prestretch Tube
using
one 2-inch bolt
two washers
one cam washer
one locknut
Finger tighten.
G. Wrap the Cable over one 3½-inch pulley and
attach it to the bottom hole on the Press Arm Flats
using
one 2-inch bolt
two washers
one locknut
H. In the middle hole on the Press Arm Flats, make a
retainer pin using
one 2-inch bolt
two washers
one 1-inch long barrel spacer
one locknut
Finger tighten.
I. Wrench tighten steps E through H. Do not
overtighten.
J. Reattach the Spring Clip to the Cable.
K. Remove excess slack by adjusting the cam washer
attached to the Prestretch Tube. Wrench tighten.
A
B
C
D
E
F
H
Each step is shown in more detail on the following page.
This completes box 4. You may move the box out of
the way.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Precor S3.45 Strength-Training bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Precor S3.45 Strength-Training in de taal/talen: Engels als bijlage per email.

De handleiding is 1,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info