389143
9
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
POWXQ5234 EN
Copyright © 2012 VARO NV P a g e | 9 www.varo.com
9.4 Installing/removing bits
9.4.1 Installing bits
Lock the switch trigger by placing the direction of rotation selector in centre position.
Open or close chuck jaws to a point where the opening is slightly larger than the bit size
you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of
the chuck jaws. Insert drill bit straight into chuck the full length of the jaws as shown in.
Tighten the chuck jaws on the drill bit.
WARNING:
Make sure to insert drill bit straight into chuck jaws.
Do not insert drill bit into chuck jaws at an angle, this could cause drill bit to be thrown from
drill resulting in possible serious personal injury or damage to the chuck.
9.4.2 Removing bits
Lock the switch trigger by placing rotation selector in centre position.
Loosen the chuck jaws from the drill bit.
Do not use a wrench to tighten or loosen the chuck jaws.
Remove the drill bit from the chuck jaws.
9.5 Adjustable torque
This drill is equipped with an adjustable torque for driving different types of screws into
different materials. The proper setting depends on the type of material and the size of
screw you are using.
TO ADJUST TORQUE: Identify the 25 position torque ring located on the front of the drill.
Rotate adjusting ring (2) to the desired setting.
1-5
For driving small screws
6-10
For driving screws into soft material
11-15
For driving screws into soft and hard materials
16-20
For driving screws in hard wood
21-25
(
)
For heavy drilling
For hammer drilling
10 DRILLING
10.1 Drilling hard smooth surfaces
When drilling hard smooth surfaces use a centre punch to mark desired hole location. This
will prevent the drill bit from slipping off centre as the hole is started. However, the low
speed feature allows starting holes without centre punching if desired. To accomplish this,
simply operate the drill at a low speed until the hole is started. The material to be drilled
should be secured in a vise or with clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled. Move the drill bit into the work
piece applying only enough pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
WARNING:
Be prepared for binding or bit breakthrough. When these situations occur, drill has a
tendency to grab and kick opposite to the direction of rotation and could cause loss of
control when breaking through material. If not prepared, this loss of control can result in
possible serious injury. If the bit jams in work piece or the drill stalls, release switch trigger
immediately. Remove the bit from the work piece and determine the reason for jamming.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus pow xq5234 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus pow xq5234 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus pow xq5234

Powerplus pow xq5234 Gebruiksaanwijzing - Nederlands - 14 pagina's

Powerplus pow xq5234 Gebruiksaanwijzing - Deutsch - 14 pagina's

Powerplus pow xq5234 Gebruiksaanwijzing - Français - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info