391293
7
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
POWXQ5102 EN
Copyright © 2015 VARO NV P a g e | 7 www.varo.com
7.1.2 Repositioning (turn) / removing the guard
To reposition/turn the guard, release the quick clamp, turn the guard, and retighten the
clamp.
To remove the guard: if installed, first remove the mounted disc, then work in the opposite
as described above under mounting/installing the guard.
7.2 Installing / replacing the grinding wheel (fig 2)
Prior to mounting/dismounting an accessory always unplug the tool.
Only Use discs of the correct dimension and of good quality. (Use fiber-reinforced
cutting/grinding discs (for stone-metal) or diamond disc (for stone) only).
The grinding disc may not touch the edge of the guard.
Press the spindle lock (fig A, n° 5) and turn the spindle until it engages in the lock. Keep
the spindle lock pressed during this procedure.
Loosen and remove the flange nut from the spindle using the spanner.
Position the disc on the flange.
Place the flange nut on the spindle and tighten using the spanner.
Release the spindle lock and check that the spindle is unlocked by rotating it.
Make sure the disc is installed in the correct way (direction of rotation)
Important! Never press the spindle lock before the motor and disc have come
to a complete standstill!
Never use the spindle lock to stop the motor. It will break.
For grinding/cutting discs up to approx. 3 mm thick, screw on the flange nut with the flat side
facing the grinding or cutting wheel. (Fig 3)
Inspect discs regularly. Worn discs have a negative effect on efficiency of the machine
and may cause severe injury to user or damage to surrounding. Replace the grinding disc
on time.
7.2.1 Test run for new grinding wheels
When starting the tool, hold the tool in a well protected area and allow the angle grinder to
reach idle speed with the grinding/cutting disc fitted in place. Vibrating wheels are to be
replaced immediately.
7.3 Mounting the side handle
The side handle can be used for both left-hand and right-hand control.
Fasten the side handle for left-hand operation on the right-hand side of the machine.
Fasten the side handle for right-hand operation on the left-hand side of the machine.
Fasten the side handle for upright working at the top of the machine.
Make sure that the side handle is fastened properly and cannot loosen
unexpectedly.
8 OPERATION
8.1 Pay special attention when starting the machine
Clamp the workpiece and make sure that the workpiece cannot slide from under the
machine during the cutting activities.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus pow xq5102 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus pow xq5102 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus pow xq5102

Powerplus pow xq5102 Gebruiksaanwijzing - Nederlands - 12 pagina's

Powerplus pow xq5102 Gebruiksaanwijzing - Deutsch - 12 pagina's

Powerplus pow xq5102 Gebruiksaanwijzing - Français - 12 pagina's

Powerplus pow xq5102 Aanvulling / aanpassing - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info