389288
7
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
POWXQ5203 EN
Copyright © 2014 VARO P a g e | 7 www.varo.com
The switch should be in 'drill’ position when drilling holes in tiles.
*(1)selector switch (4) set for Hammer mode. / (2) selector switch (4) set for drilling mode.
8.5 Reversible action (left / right) (fig 6)
The direction of rotation on your drill can be reversed.
The direction of rotation is controlled by a lever (6) located above the on/off switch (9).
With your drill held in normal operation position the direction of rotation-lever (6) should be
positioned to the right of the trigger for forward drilling operation.
The direction of rotation is in reverse (left), when the lever is turned to the left of the on/off
switch.
Don’t change the direction of rotation while your drill is still turning.
8.6 Insert a drill / bit. (fig 7)
To open the keyless chuck, hold the rear ring, turn the front ring anti-clockwise. When
jaws are open sufficiently, insert the drill / bit and re-close the chuck turning the front ring
clockwise, tighten it securely.
To unlock, turn clockwise again)
9 USE
Use only correctly sharpened drill bits which are suitable for the material being drilled.
When drilling hard materials, firm pressure is required on the power tool. However,
excessive pressure does not improve performance and places unnecessary pressure on
the tool and its bit.
Always apply pressure in straight line with the drill whiling drilling. Use enough pressure to
keep the drill biting but do not push too hard to avoid stalling the motor or damaging the
drill.
Warning! If the drill stalls, release the trigger switch immediately and remove the drill from
the work to determine the cause of stalling.
Use the auxiliary handle where possible to gain extra control and to prevent fatigue.
Use auxiliary handle supplied with the tool. Loss of control can cause
personal injury!
To minimize the chance of sudden stalling and breaking through the material, reduce the
pressure on the drill and ease the drill .
Keep the motor running when pulling the drill back out of a drilled hole. This will help
prevent jamming.
9.1 Drilling in Metal
For maximum performance, use high speed steel bits for metal or steel drilling.
Turn drilling mode selector to drilling mode.
Use a center punch to mark the hole location on the workpiece.
Begin drilling at a very low speed to prevent the drill from slipping off the starting point.
Maintain a speed and pressure which allows cutting without overheating the bit. Applying
too much pressure will: overheat the drill, wear the bearing, bend or burn bits, produce off-
center or irregular shaped holes.
When drilling large holes in metal it is recommended to drill with a small drill at first, then
finish with a larger drill, also, lubricate the drill with oil to improve drilling action and
increase drill life.
9.2 Drilling in Wood
For maximum performance, use high speed steel bits for wood drilling.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus pow xq 5203 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus pow xq 5203 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus pow xq 5203

Powerplus pow xq 5203 Gebruiksaanwijzing - Nederlands - 12 pagina's

Powerplus pow xq 5203 Gebruiksaanwijzing - Deutsch - 12 pagina's

Powerplus pow xq 5203 Gebruiksaanwijzing - Français - 12 pagina's

Powerplus pow xq 5203 Aanvulling / aanpassing - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info