582082
9
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
POWXG30010 EN
Copyright © 2015 VARO P a g e | 9 www.varo.com
9.1 Using fuel additives
The use of fuel additives will inhibit corrosion and minimize the formation of gum deposits.
Using a fuel additive can keep fuel from forming harmful deposits in the carburettor for up to
six months. Add 23 ml of fuel additive per gallon of fuel according to the instructions on the
fuel additive container. NEVER add fuel additives directly to the unit’s fuel tank.
Warning: remove fuel cap slowly to avoid injury from fuel spray. Never
operate the unit without the fuel cap securely in place.
Warning: when the engine stops, do not touch the muffler or spark plug
immediately in order to avoid any skin from burning.
10 MAINTENANCE AND REPAIR INSTRUCTIONS
Warning: to avoid serious personal injury, always turn the unit off and allow
it to fully cool down before cleaning or maintaining it.
10.1 Maintenance schedule
Perform these required maintenance procedures at the frequency stated in the table. These
procedures should also be a part of any seasonal start.
Note: some maintenance procedures may require special tools or skills. If
you are unsure about these procedures take your unit to a qualified service
dealer.
Note: Maintenance, replacement, or repair of the emission control devices
and system should be performed by qualified service dealer.
After 25 hours: Clean up any dirt on the surface, clean the air filter; check the machine
whether there is fuel or air leakage and the compression systems works normal.
After 50 hours: Remove any carbon deposition from the spark plug or change the spark plug;
remove any carbon deposition from the muffler plate in the muffler.
After 100 hours: clean the cylinder exhaust hole, the top of piston, piston ring groove and
carbon deposition from the spark plug; clean the inside of the crankcase; check the ignition
system.
After 500 hours: clean and check the engine (except the crankshaft).
10.2 Blade replacement
1. Place the 8 mm Allen wrench on the blade nut (Fig. 6).
2. While holding the Allen wrench in place, loosen the nut with a 24 mm wrench by turning it
counter clockwise (Fig. 6).
3. Remove the nut and blade. Keep the nut for new blade installation.
4. Install the new blade and nut (Fig. 7).
Note: make sure the blade edges are facing the proper direction (Fig. 7).
The unit will not function correctly if the edger blade is installed backward.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Powerplus-POWXG30010

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWXG30010 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWXG30010 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWXG30010

Powerplus POWXG30010 Gebruiksaanwijzing - Nederlands - 14 pagina's

Powerplus POWXG30010 Gebruiksaanwijzing - Deutsch - 15 pagina's

Powerplus POWXG30010 Gebruiksaanwijzing - Français - 14 pagina's

Powerplus POWXG30010 Aanvulling / aanpassing - Alle talen - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info