480959
8
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
POWX152 EN
Copyright © 2017 VARO P a g e | 8 www.varo.com
Switch off the machine and wait until the machine has come to a complete
standstill before changing the speed.
Adjust the speed to the material to be drilled and the drilling diameter.
For drilling in wood, choose a high speed.
For drilling in metal and plastics, choose a lower speed as the drilling diameter increases.
9 OPERATION
Use waste material to practice your skills and to learn operating the machine first.
When drilling through, adjust the table to make sure that the drill is alligned with the
opening in the centre of the table. If required, mark the position on the front side of pillar
and table in case the table should be set in the same position at a later time. Securely
tighten the workpiece. Toppling, turning or sliding not only results in a rough drilling hole, it
also increases the risk of the drill breaking off.
Use a piece of waste wood as a backup to reduce the risk of the workpiece splintering and
to protect the drill tip.
Place flat workpieces on a wooden underground and clamp securely to the table to
prevent them from turning. Support workpieces that are irregular of shape and cannot be
put flat onto the table.
Use the lift handles to bring the drill lift downwards. Slowly feed the dril into the
workpiece.
Drill slowly when the drill is about to break through the workpiece to prevent splintering.
9.1 Switching on and off (fig. A)
To switch the machine on, set the on/off switch (1) to ‘I’.
To switch the machine off, set the on/off switch (1) to ‘0’.
9.2 Using the laser (fig. 12)
The laser beam is used to indicate the centre location of the drill hole in case you have to drill
several holes in workpieces of the same thickness.
Place the table (5) in a horizontal position. Make sure that the drill and the opening in the
table are aligned.
Place the workpiece on the table.
Lower the drill bit until it touches the workpiece. Switch the laser (33) on by operating the
on/off switch (10).
Check that the laser cross hairs (34) align with the centre of the drill hole as marked on the
workpiece. If necessary, adjust the laser by hand. Follow the “Instructions for use” to
perform a drill hole.
After use, switch off the laser.
10 CLEANING AND MAINTENANCE
Attention ! - Before performing any work on the equipment, pull the power
plug.
The machine does not require any special maintenance.
Regularly clean the ventilation slots.
11 LUBRICATION
Turn the drill shaft to the maximum drilling depth once per 3 months and grease it slightly
with oil.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX152 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX152 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX152

Powerplus POWX152 Gebruiksaanwijzing - Nederlands - 11 pagina's

Powerplus POWX152 Gebruiksaanwijzing - Deutsch - 11 pagina's

Powerplus POWX152 Gebruiksaanwijzing - Français - 11 pagina's

Powerplus POWX152 Aanvulling / aanpassing - Alle talen - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info