676273
5
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
POWX1370 EN
Copyright © 2017 VARO P a g e | 5 www.varo.com
7.1 Testing the sequential trip safety mechanism
The nailer should not fire if the safety (3) is not depressed against the workpiece.
Make sure the switch is turned off.
Empty the magazine (5) of nails.
Check that the trigger (6) and safety (3) of the tool, move freely, without sticking.
Plug the tool into the power outlet.
Test the tool by depressing the safety (3) of the tool against the workpiece without pulling
the trigger (6). The tool must not cycle (fire). If it cycles (fires), stop immediately and take
the tool to an qualified service technician for repair.
Hold the tool away or off of the workpiece. The safety (3) of the tool should return to its
original position. Squeeze the trigger (6). The tool should not cycle (fire). If it cycles (fires),
stop immediately and take the tool to an authorized service technician.
Depress the safety (3) of the tool against the workpiece and squeeze the trigger (6). The
tool must cycle (fire) once only. If it fails to cycle (fire) or fires more than once, take it to an
authorized service technician.
Warning! Disconnect the nailer from the power outlet whenever loading it.
7.2 Loading brad nails and staples. (Fig 2&3)
Depress the lever (10) and extend the inner magazine (11) all the way out.
When loading brad nails, make sure you insert the pins of the nails on the side of the
magazine (5) with the groove in it. The brad nails should fit into the groove. When loading
staples, insert them crown up, onto the magazine (5).
Slide the extended inner magazine (11) back until the lever (10) clicks into place. Do not
force the inner magazine (11) or you may damage the tool.
When the unit is loaded with fasteners and you are ready to begin, plug the
nailer/stapler power cord (8) into a power outlet.
Hold the tool with both hands, so that the nose (4) is flat against the workpiece, making
sure that the safety (3) is also firmly against the workpiece.
Gently squeeze the trigger (6) to fire the tool.
Note: practice depth adjustment on scrap material first.
If more depth is needed, and you are nailing or stapling into a hard surface, you may apply
pressure on the top of the unit. On soft surfaces do not apply excessive pressure or the
brad nail or staple may penetrate the workpiece too deeply.
Note: each time you fire the nailer / stapler, the safety (3) must be pressed
firmly against the workpiece.
7.3 Removing jammed staples or brad nails
First, unplug the nailer / stapler. If a nail is jammed in the discharge area, simply remove it
with pliers.
If a nail is jammed in the magazine (5), depress the lever (10) and extend the inner
magazine (11) all the way out, (Fig 2&3). Use a flat screwdriver an/or needle nose plier to
free the brad nail or staple.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX1370 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX1370 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX1370

Powerplus POWX1370 Gebruiksaanwijzing - Nederlands - 8 pagina's

Powerplus POWX1370 Gebruiksaanwijzing - Deutsch - 8 pagina's

Powerplus POWX1370 Gebruiksaanwijzing - Français - 8 pagina's

Powerplus POWX1370 Aanvulling / aanpassing - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info