645078
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
POWX0650 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
7.4 Adjusting the case width (Fig. 4, Fig. 5, Fig. 6, Fig. 7)
The machine is supplied with four spacer rings (15) which are each approximately 10 mm
thick. The chase width can be adjusted by varying the amount of spacer rings fitted
between the diamond cutting discs. The chase width can be calculated by taking into
account the thickness of the spacer rings and the width of the diamond cutting discs. The
maximum chase width is approximately 44mm.
7.5 Dust extraction
The machine may only be operated when connected to a suitable vacuum device, the
vacuum device must be approved for stone dust. A dust extraction adapter (3) is supplied,
ensure that the hose is securely attached to the adapter. Stop work immediately when the
vacuum device breaks down. Switch the machine off and restore the vacuum device. The
vacuum device must be suitable for the type of material you work with. Use a special
vacuum device when working with toxic materials or where toxic dust is produced. Use of
a household vacuum cleaner may damage your health.
For best results use a wet and dry vacuum device fitted with an appropriate filter. If in
doubt seek expert advice.
8 OPERATION
Mark the line of cut before starting work, hold the machine tightly with both
hands. (Fig. 8)
1. Set the chase depth. Place the front roller wheel of this machine firmly against the wall.
Switch the machine on and gently lower the machine towards the wall until the rotating
diamond cutting discs plunge into the wall, hold the machine tightly with both hands.
2. Carry out the cut steadily, evenly and with moderate pressure appropriate to the material
being cut. Ensure you work in the correct direction! Always work against the direction of
rotation as shown on the machines protective guard to avoid the risk of the machine
being forced uncontrolled of the cut.
3. After completing the cut, retract the machine slightly, switch off and remove from the cut.
Allow the diamond cutting discs to stop before putting the machine down. Do not attempt
to brake the diamond cutting discs by applying lateral pressure.
Remove the remaining masonry in the chase using the masonry breaking tool provided.
It is not possible to make curved cuts with the machine as the diamond cutting discs may
seize in the cut.
Paving slabs or similar must be placed on a solid surface or be otherwise securely
supported before starting the cut to avoid breakage.
When cutting especially hard material, e.g. concrete with high gravel content, the diamond
cutting discs can overheat and become damaged. This is indicated by a ring of sparks that
rotates with the diamond discs. In this case, interrupt the cutting process and allow the
diamond discs to cool down by running the machine at no-load for a short time.
Noticeably decreasing work progress and a rotating spark ring indicate that the diamond
cutting discs have become blunt.
9 CLEANING AND MAINTENANCE
WARNING: Disconnect the unit from the mains before carrying out any
maintenance or adjustments.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX0650 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX0650 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX0650

Powerplus POWX0650 Gebruiksaanwijzing - Nederlands - 11 pagina's

Powerplus POWX0650 Gebruiksaanwijzing - Deutsch - 12 pagina's

Powerplus POWX0650 Gebruiksaanwijzing - Français - 11 pagina's

Powerplus POWX0650 Aanvulling / aanpassing - Alle talen - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info