644862
8
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
POWX0042LI EN
Copyright © 2017 VARO P a g e | 8 www.varo.com
8.2 To install or remove the battery pack
8.2.1 To remove the battery
Depress both the battery release buttons and gently pull the battery out of the drill.
8.2.2 To install the battery
Hold the drill upright in one hand and the battery in your other hand. While pressing with two
fingers on the battery release buttons, insert the battery until it clicks into place. Do not use
excessive force when inserting the battery. If the battery does not slide in easily, it is not being
inserted correctly. It is also possible that there could be damage to the battery, battery
terminals or the drill.
8.3 Installing/removing bits and drills
8.3.1 Installing bits/drills
Lock the switch trigger by placing the direction of rotation selector in centre position.
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you
intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the
chuck jaws. Insert drill bit straight into chuck the full length of the jaws as shown in. Tighten
the chuck jaws on the drill bit.
WARNING: Make sure to insert drill bit straight into chuck jaws.
Do not insert drill bit into chuck jaws at an angle, this could cause drill bit to be thrown from
drill resulting in possible serious personal injury or damage to the chuck.
8.3.2 Removing bits/drills
Lock the switch trigger by placing rotation selector in centre position.
Loosen the chuck jaws from the drill bit.
Note: Rotate chuck body in the direction of the arrow marked. Release to loosen chuck jaws.
Do not use a wrench to tighten or loosen the chuck jaws.
Remove the drill bit from the chuck jaws.
8.4 General hints for drilling
8.4.1 Drilling in all materials
Always use sharp drill bits. Mark the place where you would like the hole to be drilled.
Commence with a slow speed to start the hole. Reduce your pressure on the drill when the
drill bit is about to break through the material.
8.4.2 Metal drilling
Support thin material with a piece of scrap wood. Use a center punch to mark the position of
the hole. If drilling a large hole, use a small size drill bit first to establish a pilot hole then use
the required large size drill bit. Use only HSS (High Speed Steel) drill bits or those
recommended for metal use. When drilling into iron or steel, use no lubricant but withdraw the
drill regularly to assist cooling.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX0042LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX0042LI in de taal/talen: Engels als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWX0042LI

Powerplus POWX0042LI Gebruiksaanwijzing - Nederlands - 12 pagina's

Powerplus POWX0042LI Gebruiksaanwijzing - Deutsch - 13 pagina's

Powerplus POWX0042LI Gebruiksaanwijzing - Français - 13 pagina's

Powerplus POWX0042LI Aanvulling / aanpassing - Alle talen - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info