795364
5
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
POWAIR0802 EN
Copyright © 2014 VARO P a g e | 5 www.varo.com
every two hours of use. This must be done directly along the male coupler or the screw
(OIL) provided for the purpose on the side of the tool’s housing.
Automatic lubrication is also possible using the supplied mini oiler that you have to install
between the threaded connector of the tool and the male coupler. Make sure that the oiler
is always filled with suitable oil.
Fig. 1
1. Tool
2. Quick connector
3. Quick coupler
4. Air hose
5. Quick connector
6. Quick coupler
7. Lubricator
8. Regulator (0-8.5 bar)
9. Filter
10. Cut-off valve
11. Air compressor
8 LOADING AND OPERATION
8.1 Drill Bit Installation
Select the drill bit needed for the drilling you wish to perform.
Open up the jaws of the drill by turning the chuck.
When the jaws are open wide enough to insert the drill bit, slide the bit into the drill
chuck as far as possible.
By hand, turn the drill chuck to tighten the jaws and make sure very tight.
8.2 Using the Air Drill
CAUTION: Do not operate the Air Drill before placing the drill bit on the
material.
WARNING: Do not touch the DRILL CHUCK or the drill bit while the Air
Drill is spinning.
Mark the material on the spot for drilling the hole. Make sure your drill bit is the correct
size for the hole you need to make.
Clamp the material in a vise to make sure the material does not move or begins to spin
while drilling.
Wear eye protection to guard against flying wood or metal.
Set the compressor’s pressure regulator to 90 PSI. Do not set the compressor’s outlet
regulator over 90 PSI.
Connect the air drill to the air compressor’s hose. If leaking is detected, disconnect the
air hose and repair before use.
Hold the air drill firmly. Place the drill bit on the spot marked in Step 1.
To begin drilling, press the trigger.
Your air drill has a variable speed for drilling. To vary the speed of the drilling action,
vary the pressure on the trigger.
Drill only as deep as necessary. Do not drill deeper than necessary into walls or other
areas where you cannot identify any possible hazards behind the drilling surface.
When you have drilled the hole, remove the drill bit from the hole while the air drill is
still spinning. This is to prevent the drill getting caught in the hole and causing damage.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWAIR0802 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWAIR0802 in de taal/talen: Engels als bijlage per email.

De handleiding is 0.25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POWAIR0802

Powerplus POWAIR0802 Gebruiksaanwijzing - Nederlands - 10 pagina's

Powerplus POWAIR0802 Gebruiksaanwijzing - Deutsch - 10 pagina's

Powerplus POWAIR0802 Gebruiksaanwijzing - Français - 10 pagina's

Powerplus POWAIR0802 Aanvulling / aanpassing - Alle talen - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info