481001
6
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
POW7490 EN
Copyright © 2015 VARO P a g e | 6 www.varo.com
Check with a qualified electrician or service personnel if the grounding instructions are not
completely understood, or if in doubt as to whether the tool is properly grounded.
6.2 Diamond blades
Only use 180mm diameter Continuous Rim Wet Diamond blades.
DO NOT use larger, segmented or 'turbo' blades, wood sawing blades, or any other
cutting device. Severe bodily injury, and damage to your saw can occur.
Inspect blades daily for cracks or uneven wear. Discard cracked, chipped or bent blades!
Ensure the blade is mounted with the rotation arrow in the proper direction and is securely
tightened with a wrench.
Always ensure a continuous flow of water on both sides of the blade before cutting any
material.
Do not operate the machine without all safety guards in position
Do not force the material into the blade. Let the blade cut at its own speed.
7 ASSEMBLY
ATTENTION! Disconnect the power plug before carrying out any
adjustments or maintenance.
7.1 Mounting the riving knife (fig. 1)
Unscrew the two (crosshead) screws and place the foot of the riving knife under the table.
Place the small plate (2 holes with thread) under the foot of the riving knife
Connect the riving knife with the two screws and the plate
7.2 Mounting the cutting disc (fig. 2 & 3)
Unscrew two screws out of lower blade guard and remove the guard. (fig. 2)
Dismount nut (counterclockwise) and outer flange
Place blade on the inner flange
Mount outer flange and nut (clockwise) again (fig. 3)
Place the lower blade guard back in position and connect the two screws
7.3 Mounting the upper blade guard (10) (fig. 4)
Slide the guard in horizontal position across the riving knife.
Connect the guard to the riving knife with the wing nut bolt and the locknut
Be aware that the guard is connected under the lockpin. The lock-pin prevents the guard
falling backwards.
7.4 Mounting the adjustable fence
Connect the knob (7) with the fence (3) by using the plate (1 hole with thread); do not
tighten the knob yet.
Slide the complete fence with (loosen) knobs onto the table; the plates on the inner side of
the table.
Set the required distance.
Tighten the knobs by rotating them (clockwise).
Place the water reservoir (4) under the table
8 OPERATION
The tile cutter may only be used as a fixed tool and should be screwed down to a level
and horizontal surface.
Use the screw holes in the base of the machine.
Keep water full in the tank when you operate the cutter.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POW7490 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POW7490 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POW7490

Powerplus POW7490 Gebruiksaanwijzing - Nederlands - 10 pagina's

Powerplus POW7490 Gebruiksaanwijzing - Deutsch - 11 pagina's

Powerplus POW7490 Gebruiksaanwijzing - Français - 11 pagina's

Powerplus POW7490 Aanvulling / aanpassing - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info