480975
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
POW222 EN
Copyright © 2015 VARO P a g e | 5 www.varo.com
Press the spindle lock button(12) and loosen the flange nut using the pin spanner.
Remove the diamond cutting discs and the spacer rings.
Place one diamond cutting disc onto the motor flange.
Slide space rings (as required) followed by the remaining diamond cutting disc on the
spindle.
Press the spindle lock button(12) and screw the flange nut onto the spindle using the pin
spanner.
Rotate the depth stop upwards, and replace the depth stop
Put screws back in place using the hex key. (Caution! Do not forget the washer and lock
washers replace the depth stop fixing screw)
Caution! Always replace diamond cutting discs in pairs. To loosen /
tighten discs: Press spindle lock button, turn disc by hand until it locks,
then loosen / tighten with pin spanner.
7 DEPTH ADJUSTMENT (FIG. 5)
Loosen the fixing screw for depth stop (4)and set the require depth.
Re-tighten the fixing screw for depth stop select a chase depth approximately 3mm deeper
that the actual required depth to compensate for unevenness in the wall surface.
8 TURNING THE MACHINE ON/OFF (FIG. 6)
Press the safety switch (10) and pull the trigger(3) ,the machine is on.
Release the trigger ,the machine is off.
The machine fitted with a soft start mechanism
The machine has an overload protection device. In case of overload, it will shut down
automatically. Release the trigger and remove the machine from the work-piece. Allow to
cool for a few minutes, then restart and run the machine at no-load for approximately one
minute to cool the machine down faster.
9 ADJUSTING THE CHASE WIDTH (FIG. 7 - 9)
The machine is supplied with two spacer rings (10mm and 15 mm). The chase width is
adjusted by varying the amount of spacer rings between the diamond cutting discs. Mind
the width of the diamond cutting discs. The maximum chase width is approximately 29mm.
Make sure at least 5mm thread remains to tighten the outer spanner ring.
10 DUST EXTRACTION (FIG. 10)
The wall slotter is equipped with a dust extractor socket. You can connect your vacuum
cleaner to the socket at the rear of the wall slotter. If you require a special adapter, please
contact the manufacturer of your vacuum cleaner.
11 OPERATION (FIG. 11)
Mark the line of cut before starting work, hold the machine tightly with both
hands.
Set the chase depth, press the front edge of the depth stop, firmly against the wall. Switch
the machine on and gently lower the machine towards the wall until the rotating diamond
cutting discs plunge into the wall ,Hold the machine tightly with both hands.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POW222 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POW222 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POW222

Powerplus POW222 Gebruiksaanwijzing - Nederlands - 9 pagina's

Powerplus POW222 Gebruiksaanwijzing - Deutsch - 9 pagina's

Powerplus POW222 Gebruiksaanwijzing - Français - 9 pagina's

Powerplus POW222 Aanvulling / aanpassing - Alle talen - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info