751773
23
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
Generating Power to the World
Page 23 of 26
PT-10000/PT-12000 Operators Manual
GENERATOR ASSEMBLY INFORMATION
EXCITER TYPE GENERATOR
The exciter pole pieces contain residual magnetism, which sets up lines of force
across the air gap to the exciter armature. When the exciter begins to rotate a voltage
is induced and current flow is initiated in the exciter armature AC windings. This voltage
is fed to the rotating rectifier assembly, rectified and fed to the alternator field, which
sets up lines of force across the air gap to the alternator stator windings and to the
output circuit. A static voltage regulator is connected to the generator output. The
regulator will rectify part of the output voltage to provide a DC voltage to the exciter field
coils. This will increase the density of the lines of force in the exciter, increasing the
voltage induced into the exciter armature windings, and therefore, to the rotating
rectifiers. The rotating rectifier output will be increased which increase the alternator
field strength and generator output will build up its rated voltage. Adjustment of the
generator output to the rated voltage level is accomplished by controlling the current fed
to the exciter field coils. Regulation is automatic with the static type voltage regulator.
An additional voltage adjustment range is provided if desired by turning the Voltage
Adjust Rheostat.
ELECTRONIC VOLTAGE REGULATION
Electronic Voltage Regulator (EVR) also referred to, as an Automatic Voltage
Regulator (AVR) is a very reliable device, which uses solid-state electronics to maintain
voltage accuracy at ±2% of the regulated voltage. The Voltage Regulator is designed to
automatically regulate and maintain the generated AC voltage throughout the load
range that is from no load to full load.
VOLTAGE CONNECTION
The generator may be connected at the terminal board to deliver 120/240 volts to
a 3 wire grounded neutral system.
If all equipment requires 120-volts then the 120-volt connection is preferred, even if
two lines leave the same switch box. The two lines at the inputs to the switch box are
both connected to the un-grounded 120-volt lines from the generator.
The 120-volt connection enables the Electronic Voltage Regulator (EVR) to hold the
voltage very close to the 115 or 120 volts, as initially adjusted, regardless of the power
distribution amount the different distribution lines. The 120-volt connection is
recommended if the entire electrical load requires only 115 or 120 volts. Although the
120/240-volt connection may also be used when all loads requires only 110 volts, it
should be pointed out that this connection, the 240-volts, is regulated and the lightly
loaded phase, or line, will deliver a high line to neutral voltage and the heavily loaded
phase will deliver a low line to neutral voltage. The heavily loaded line may have such a
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw PowerTech PTGK-15 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van PowerTech PTGK-15 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info