685327
4
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
Depending upon the location of your Marine Power System; either above or below the water
line, some additional components may be required to complete the installation. See the following pages
for details on each system.
Cooling Water Supply Through-Hull Seacock Fitting (Flush Hull Type)
Shut OFF Valve
Seawater Strainer
Fuel System Primary Filter / Water Separator
Shut OFF Valve
Exhaust System Siphon Break
Hydro-Muffler
Zinc Anode
Shut OFF Valve or Cover
AC/DC Electrical Systems
Ship to Shore Transfer Switch
Remote Gauge Panel
INSPECTION of EQUIPMENT:
Prior to accepting your Marine Power System, check the unit for any shipping damage and be
sure all accessories ordered are present. Check the contents against the packing list and report any loss
or damage to the transportation company.
RIGGING and LIFTING:
Because of the size and weight of the unit, careful planning for rigging and lifting must be
considered. Each unit is equipped with lifting eyes that are designed to carry the full weight of the
generator. These lifting eyes are located on the upper engine section of the unit and allow the unit to be
hoisted horizontally. In some situations the hatchway may not be large enough to accommodate the unit
in the horizontal position. Therefore hoisting the unit in a vertical position will be necessary and
specialized rigging may be needed to accomplish vertical hoisting. Be especially careful that the rigging
does not interfere with or damage components on the unit. Never attach rigging to components or
accessories, remove these parts if necessary and re-attach after the unit is in place. Special rigging work
is best done by competent and experienced personnel working with proper equipment. Avoid short cuts.
GENERATOR LOCATION and MOUNTING:
As previously mentioned the location of the Marine Power System in the vessel is extremely
important. Follow the vessel manufacturer recommendations should they apply to your installation. All
key factors must be considered when choosing the mounting location for the unit. The engine and
generator end are mounted to a heavy gauge sheet metal base pan by 4 flexible isolators that help
prevent the transfer of vibrations from the generator to the mounting location. The unit must be
orientated on a level and structurally sound mounting platform, and securely bolted into place. Once the
unit mounting is completed the installer may begin attaching the component systems.
VENTILATION:
Most vessels are equipped with an ambient air ventilation system. If your vessel is not equipped
or insufficiently equipped to support the extra demand of a Marine Power System, provisions must be
made to install or increase the volume of ambient air into the area while providing for expulsion of hot
air and hazardous fumes.
2
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw PowerTech Marine Power System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van PowerTech Marine Power System in de taal/talen: Engels als bijlage per email.

De handleiding is 0,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info