491891
3
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
English
Français
Italiano
Español
Nederlands
Deutsch
3
En
Connecting up (continued)
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for
ventilation to improve heat radiation (at least 40 cm at top, 10 cm at rear,
and 20 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure
reliable operation of the product, and to protect it from overheating. To
prevent fire hazard, the openings should never be blocked or covered with
items (such as newspapers, table-cloths, curtains) or by operating the
equipment on thick carpet or a bed.
D3-4-2-1-7b*_A1_En
STEREO RECEIVER
VOLUME
TUNE
/
PRESET
MEMORY
STANDBY
A
SPEAKERS
B
PHONES
TONE
BALANCE
S
X
-
20
STANDBY
ON
Connecting the speakers
Make sure you connect the speaker on the right to the right (R) terminal
and the speaker on the left to the left (L) terminal. Also make sure the
positive and negative (+/–) terminals on the receiver match those on the
speakers.
1
Twist the cable cores.
2
Loosen the nut on the SPEAKERS terminal, and insert the speaker
cable into the exposed hole in the terminal shaft.
3
Retighten the terminal nut.
12 3
10 mm
CAUTION
When using only one set of speaker terminals (SPEAKERS A or
SPEAKERS B), the speaker used should have a nominal impedance
between 4
Ω
and 16
Ω
. When using both sets of terminals, the
connected speakers should have nominal impedance between 8
Ω
and 16
Ω
. Consult the instructions accompanying your speakers
for details regarding the impedance value.
These speaker terminals carry
HAZARDOUS live voltage
. To prevent
the risk of electric shock when connecting or disconnecting the
speaker cables, disconnect the power cord before touching any
uninsulated parts.
Connecting the FM and AM antennas
Connect FM wire antenna and the the AM loop antenna
as shown below.
AM LOOP
FM UNBAL
75
ANTENNA
To power outlet
Connecting your equipment
Connecting the playback components
1
Connect the audio outputs of your SACD player (or CD player) to the
SACD/CD IN jacks on this receiver.
2
Connect the audio outputs of your network audio player to the
NETWORK IN jacks on this receiver.
You may connect other audio components furnished with analog audio
output jacks. If you wish to connect a portable audio player or other
component furnished with mini-plug output jacks (or headphone jacks),
use of a commercially available conversion plug will be necessary.
Connecting the cassette deck
Connect the audio outputs of your cassette deck (or other recorder)
to the RECORDER IN jacks on this receiver. Then connect the audio
inputs on the cassette deck to the RECORDER OUT jacks on this
receiver.
This will allow you to make recordings from the components connected to
this receiver.
Connecting a turntable
Connect the audio outputs of your turntable to the PHONO IN jacks
on this receiver.
Important
The
SIGNAL GND
terminal is provided to reduce noise when
connecting the unit to components such as an analog turntable.
Do not connect the
PHONO (MM)
terminals to any component other
than a turntable; also, do not connect to a turntable equipped with
built-in equalizer. An excessively high sound output may be produced,
resulting in damage to your speakers or other devices.
The unit’s
PHONO (MM)
terminals are designed to be used with
turntables equipped with MM (moving-magnet) type cartridges.
Turntables equipped with MC (moving-coil) cartridges cannot be used.
Plugging the receiver
Only plug in after you have connected all your components to this receiver,
including the speakers.
1
Plug the supplied power cord into the AC IN socket on the back of
the receiver.
2
Plug the other end into a power outlet.
AC IN
CAUTION
Handle the power cord by the plug part. Do not pull out the plug by
tugging the cord, and never touch the power cord when your hands are
wet, as this could cause a short circuit or electric shock. Do not place
the unit, a piece of furniture, or other object on the power cord or pinch
the cord in any other way. Never make a knot in the cord or tie it with
other cables. The power cords should be routed so that they are not
likely to be stepped on. A damaged power cord can cause a fire or give
you an electric shock. Check the power cord once in a while. If you find
it damaged, ask your nearest Pioneer authorized independent service
company for a replacement.
SX-20_YXE8_book.indb 3SX-20_YXE8_book.indb 3 2012/08/03 9:33:402012/08/03 9:33:40
3

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Pioneer-SX-20-S

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SX-20-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SX-20-S in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 11,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Pioneer SX-20-S

Pioneer SX-20-S Gebruiksaanwijzing - Nederlands - 15 pagina's

Pioneer SX-20-S Gebruiksaanwijzing - Deutsch - 15 pagina's

Pioneer SX-20-S Gebruiksaanwijzing - English - 15 pagina's

Pioneer SX-20-S Gebruiksaanwijzing - Français - 15 pagina's

Pioneer SX-20-S Gebruiksaanwijzing - Italiano - 15 pagina's

Pioneer SX-20-S Gebruiksaanwijzing - Espanõl - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info