612929
4
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
4
1 Preparations
1.1 Confirm the products
The operations necessary to install the Pedaling Monitor System on the customer’s bicycle depend on which System it
is; SGY-PM910HL/HR or SGY-PM910H2, and on which cycle computer is being used; SGX-CA500, SGX-CA900, or
some other manufacturer’s product.
1.2 Outline of procedure
1.2.1 For the SGY-PM910HL/HR with an ANT+ cycle computer
Single Power Meter Mode:(SGY-PM910Hl/HR Factory Default Mode)
1. [3.1Temporarily affix the Magnet]: Attach the magnet to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should flash
Orange for ten seconds
3. [3.2 Magnet Detection]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the
magnet.
4. [3.3.3 Fixing the Magnet]: Fix the magnet in place.
5. [4 Pairing with the Cyclocomputer]: Pair the sensor with the cycle computer.
6. [5 Zero Calibration]: Carry out Zero Calibration.
1.2.2 For the SGY-910H2/(HL+HR) with an ANT+ cycle computer
Dual Power Meter Mode:(SGY-PM910H2 Mode on shipment from Installation center)
1. [3.1Temporarily affix the Magnet]: Attach the left and right magnets to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should light
Orange for ten seconds.
3. [2.2 Mode Switching]: If the LED flashed in step 2, it is necessary to switch the mode to Dual Power Meter
Mode.
Push the button on the right side transmitter for two seconds, and the LED will flash quickly in Orange for ten
seconds. While this is happening, release the button and press it again for two seconds. The LED will then light in
Orange for ten seconds.
4. [3.2.2Detecting the Magnet Position]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the magnet.
5. [3.3.3Fixing the Magnets]: Fix the magnet in place.
6. [4Pairing with the Cyclocomputer]: Pair the sensors with the cycle computer using the device number of the
right side sensor.
7. [5Zero Calibration]: Carry out Zero Calibration.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SGY-PM910H2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SGY-PM910H2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Pioneer SGY-PM910H2

Pioneer SGY-PM910H2 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Espanõl - 234 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info